Speedaire
®
3/8" Air
Composite Drill
Speedaire Air Composite Drill is used for maintenance, light
assembly or automotive repair. Comes with comfort grip, precise throttle control,
and durable motor and gears.
Figure 1
Unpacking
Specifications
When unpacking the unit, carefully
look for any damage that may have
occurred during transit. Check for
loose, missing or damaged parts.
General Safety Information
1.
For Additional Safety
information Consult:
Your employer, union, and/or trade
association.
US Department of Labor (OSHA);
www.osha gov.
" Safety Code For Portable Air
Tools" (B186.1) available from:
www.ansi.org.
Projectile Hazards
Always wear impact-resistant eye
and face protection when involved
with or near the operation, repair
or maintenance of the tool or
changing accessories on the tool.
Be sure all others in the area are
wearing impact-resistant eye and
face protection.
Even small projectiles can injure
eyes and cause blindness.
Entanglement Hazards
Keep away from rotating bit and
chuck.
2.
3.
Bit Binding Hazards
Always use sharp bits.
Reduce downward pressure at
breakthrough.
ANSI recommends the use of a
support handle on drills with a
chuck capacity larger than 3/8 in. or
10mm.
Workplace Hazards
Slip/Trip/Fall is a major cause of
serious injury or death. Beware of
excess hose left on the walking or
work surface.
High sound levels can cause perma-
nent hearing loss. Use hearing
protection as recommended by your
employer or OSHA regulation (See)
29 CFR part 1910).
Maintain a balanced body position
and secure footing.
Repetitive work motions, awkward
positions and exposure to vibration
can be harmful to hands and arms.
If numbness, tingling, pain or
whitening of the skin occurs, stop
using tool and consult a physician.
Avoid inhaling dust or handling
debris from the work process which
can be harmful to your health. Use
dust extraction and wear respir-
atory protective equipment when
working with materials which
produce airborne particles.
Proceed with care in unfamiliar
surroundings. Hidden hazards may
exist, such as drilling into electric or
other utility lines.
4.
5.
Chuck Capacity
Free speed (No Load)
Length
Average air consumption
Air inlet
Maximum Air Pressure
Weight
Hose Size
...................................3/8"
............. 2000 RPM
.......................................... 8.26 in
........... 3.5 CFM
...................................... 1/4" NPT
.................. 90 PSI
....................................... 1.69 LBS
.................................... 3/8" I.D.
Includes:
1 - Air Drill
1 - Key
WARNING
To reduce risk of injury, everyone
using, installing, repairing,
maintaining, changing
accessories on, or working near
this tool must read and
understand these instructions
before performing any such task.
This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT
PROBLEMS. To help recognize this
information, observe the following symbols.
Safety Guidelines
Danger indicates an imminently
hazardous situation which, if not
The drill bit can suddenly
bind and cause the work
piece or tool to rotate, causing arm and shoulder
injuries.
able to handle the bulk, weight and power of this tool.
avoided, WILL result in death or serious injury.
Warning indicates a potentially
hazardous situation which, if
not avoided, COULD result in death or serious injury.
Caution indicates a potentially
hazardous situation which, if
Do not wear jewelry or
loose clothing.
not avoided, MAY result in minor or moderate injury.
Notice indicates important
information, that if not followed,
may cause damage to equipment
NOTICE
You can be cut or burned if you
come in contact with the drill bit,
chips or work surface.
Use intermittent drill pressure to
avoid long shaved chips.
Scalping can occur if hair is not
kept away from tool and
accessories. Choking can occur
if neck wear is not kept away
from tool and accessories.
Operators and maintenance
personnel must be physically
10D240
in Taiwan
5S6846
04634
STC100
06/11
#804
