NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole
discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click
on the support tab for this product.
Team Spektrum™ FPV Edition
Swift 2 FPV Camera with OSD
SPMVC621
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di istruzioni
EN
5-36V GND Video Audio VBA
T+
GND OSD
MIC
UP
DOWN
MENU
LEFT
RIGHT
5-36V GND Video Audio VBA
T+
GND OSD
MIC
5-36V GND Video Audio VBA
T+
GND OSD
MIC
UP
DOWN
MENU
LEFT
RIGHT
5-36V GND Video Audio VBA
T+
GND OSD
MIC
5-36V GND Video Audio VBA
T+
GND OSD
MIC
UP
DOWN
MENU
LEFT
RIGHT
5-36V GND Video Audio VBA
T+
GND OSD
MIC
Camera Back
Camera Back
OSD Extension
OSD Extension
OSD Switch Board
5-Pin Harness
• VBAT+ (Blue)
• Audio out (White)
• Video out (Yellow)
• Ground wire (Black)
• DC 5–36V in (Red)
The camera’s built-in OSD and camera functions can be controlled by the OSD switch board. An
extension is provided to make remote access to the OSD switch board easier.
1.
Use the 3x5mm screws and lock nuts to secure the camera mount to the airframe.
2.
Use the 3x5mm screws and nylon washers to secure the camera to the pivot point on both
sides of the mount
3.
Use the 2x4mm screws and nylon washers to secure the camera angle.
There are two harness options included with
the camera.
1. A basic 3-pin video cable is included for
simple connections. Plug the cable into the
far side of the connector closest to the case and connect it to
the SPMVTM150 for a solder free connection.
2. An advanced 5-pin harness is also included which has wires for
audio and voltage detection.
3. Connect the VBAT wire to the positive wire on the power supply
for the OSD voltage reading.
4. Connect the OSD extension cable for easy access to the camera settings.
• Team Spektrum FPV Edition Swift 2 Camera
• Video Cables (2)
• OSD Switch Board and Extension Cable
• Camera Mount
• Small Hardware (nylon washers, 3x5mm screws, 2x4mm screws, 3mm lock nuts)
• Optional Camera Case
Quick Settings:
Long Press UP Button:
Press for three seconds to access the settings for the OSD screen.
Long Press LEFT Button:
Press for three seconds to calibrate the voltage. When the voltage text
flashes, press UP or DOWN buttons to make adjustments to the displayed value.
Long Press DOWN Button:
Press for five seconds to reset the OSD settings to default.
Long Press RIGHT Button:
Press for three seconds to switch between camera presets.
1. Press the middle button to change the selec-
tion ON or OFF, then move to POS to enter the
position adjustment.
2. Press up/down, left or right to navigate the
menu. Press up/down to change the display
location when the cursor is on a POS selection.
CLR:
Clear the ID field.
Alarm:
Low voltage alarm trigger point. Set this
value to the voltage the OSD should trigger the
low voltage warning.
SCENE:
This selection offers the following set-
tings; Personal, Lightrax Outdoor, Indoor, Cloudy,
Twilight. Hold the right button down at any time when not in the menu to cycle through the Scene
options without having to enter the menu.
SYSTEM:
Displays whether the camera is operating in NTSC or PAL mode.
PILOT:
Activate or disable the pilot ID. When active the pilot ID is displayed on-screen during operation.
TIMER:
Activate or disable the timer. When active the timer begins the counting at power up
on-screen. When disabled the Timer is not displayed on-screen.
VOLTAGE:
Activate or disable the timer. When active the battery voltage is displayed on-screen.
HORIZON:
Activate or disable a horizontal reference line, which some pilots prefer to use to help
align the flight path.
EXIT:
Select this option to exit the menu.
1. Press the middle button on the OSD Switch Board to access the main camera menu, then
move to POS to enter the position adjustment.
2. Press up/down, left or right to navigate the menu. Press up/down to change values when the
cursor is on a POS selection.
3. Select Return to back out of a sub-menu to the main menu.
•
Select Reset to change all camera settings
back to factory default.
•
Exit Saves settings and returns to normal
camera operation
CAMERA-OSD SWITCH CONNECTION
CAMERA TO VIDEO TRANSMITTER CONNECTION
BOX CONTENTS
CAMERA MOUNTING
OSD MENU
CAMERA MENU
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ
.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
EXPOSURE
SHUTTER AUTO
BRIGHTNESS 050
AGC ----
DWDR OFF
RETURN
RET
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
MANUAL
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
BLC
SETUP
EXPOSURE
BACKLIGHT
BLC
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
WB MANUAL
COLOR TEMP
MANUAL
BLUE 045
RED 064
RETURN
RET
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
AUTO
DPC
LANGUAGE
ENGLISH
RESET
EXIT
IMAGE ADJ.
LENS SHAD.
ON
2DNR OFF
MIRROR OFF
FONT COLOR
CONTRAST 110
SHARPNESS
026
DISPLAY
LCD
NEG. IMAGE
OFF
RETURN
RET
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE ENGLISH
RESET
EXIT
1234567890ABC
DEFGHIJKLMNOPQ
RSTUVWXYZ=/&:.
CLR
ALARM
SCENE
SYSTEM
PILOT
TIMER
VOLTAGE
HORIZON
EXIT
SPEKTRUM
:14.8V
:PERSONAL
:ON POS
:ON POS
:ON POS
:ON POS
:OFF POS
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT AUTO
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
D&N AUTO
D->N LEVEL
144
D->N DELAY
3 SEC
N->D LEVEL
112
N->D DELAY
1 SEC
RETURN
RET
D&N B/W
GAMMA 0.50
PED LEVEL
017
COLOR GAIN
176
RETURN
RET
BURST OFF
IR SMART
ON
IR LEVEL
HIGH
RETURN
RET
LENS SHAD.
LEVEL
020
LCD ADJUST
IR SMART
IRGAIN
066
HEIGHT 006
WIDTH 016
LEFT/RIGHT 001
TOP/BOTTOM 004
RETURN
RET
AREA SEL.
AREA1
AREA STATE
ON
GAIN 168
HEIGHT 005
WIDTH 005
LEFT/RIGHT 004
TOP/BOTTOM 004
RETURN
RET
HLC
LEVEL 200
RETURN
RET
FONT COLOR
LEVEL
003
ID & TITLE
003
RESET\EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ
.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
EXPOSURE
SHUTTER AUTO
BRIGHTNESS 050
AGC ----
DWDR OFF
RETURN
RET
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
MANUAL
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
BLC
SETUP
EXPOSURE
BACKLIGHT
BLC
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
WB MANUAL
COLOR TEMP
MANUAL
BLUE 045
RED 064
RETURN
RET
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
AUTO
DPC
LANGUAGE
ENGLISH
RESET
EXIT
IMAGE ADJ.
LENS SHAD.
ON
2DNR OFF
MIRROR OFF
FONT COLOR
CONTRAST 110
SHARPNESS
026
DISPLAY
LCD
NEG. IMAGE
OFF
RETURN
RET
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE ENGLISH
RESET
EXIT
1234567890ABC
DEFGHIJKLMNOPQ
RSTUVWXYZ=/&:.
CLR
ALARM
SCENE
SYSTEM
PILOT
TIMER
VOLTAGE
HORIZON
EXIT
SPEKTRUM
:14.8V
:PERSONAL
:ON POS
:ON POS
:ON POS
:ON POS
:OFF POS
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT AUTO
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
D&N AUTO
D->N LEVEL
144
D->N DELAY
3 SEC
N->D LEVEL
112
N->D DELAY
1 SEC
RETURN
RET
D&N B/W
GAMMA 0.50
PED LEVEL
017
COLOR GAIN
176
RETURN
RET
BURST OFF
IR SMART
ON
IR LEVEL
HIGH
RETURN
RET
LENS SHAD.
LEVEL
020
LCD ADJUST
IR SMART
IRGAIN
066
HEIGHT 006
WIDTH 016
LEFT/RIGHT 001
TOP/BOTTOM 004
RETURN
RET
AREA SEL.
AREA1
AREA STATE
ON
GAIN 168
HEIGHT 005
WIDTH 005
LEFT/RIGHT 004
TOP/BOTTOM 004
RETURN
RET
HLC
LEVEL 200
RETURN
RET
FONT COLOR
LEVEL
003
ID & TITLE
003
IMPORTANT:
Consult local laws and ordinances
before operating FPV (first person view) equipment.
In some areas, FPV operation may be limited or
prohibited. You are responsible for operating this
product in a legal and responsible manner.
LIMITED WARRANTY
What this Warranty Covers
- Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that
the product purchased (the “Product”) will be free from defects in materials and workmanship for
a period of 1 year from the date of purchase.
What is Not Covered
- This warranty is not transferable and does not cover (i) cosmetic damage,
(ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due
to improper use, installation, operation or maintenance, (iii) modification of or to any part of the
Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v)
Product not purchased from an authorized Horizon dealer, (vi) Product not compliant with applicable
technical regulations, or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED
THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
- Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall
be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon
to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase
is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,
REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE,
STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual
price of the Product on which liability is asserted. As Horizon has no control over use, setup, final
assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or
injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser
or user are not prepared to accept the liability associated with the use of the Product, purchaser is
advised to return the Product immediately in new and unused condition to the place of purchase.
Law
- These terms are governed by Illinois law (without regard to conflict of law principals). This
warranty gives you specific legal rights, and you may also have other rights which vary from state to
state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services - Your local hobby store and/or place of purchase cannot provide
warranty support or service. Once assembly, setup or use of the Product has been started, you must
contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions
and service you in the event that you may need any assistance. For questions or assistance, please visit
our website at horizonhobby.com, submit an inquiry to productsupport@horizonhobby.com or call the
toll-free telephone number referenced in the Warranty and Service Contact Information section to speak
with a Product Support representative.
Inspection or Services
- If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online Service Request submission
process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)
number. Pack the Product securely using a shipping carton. Please note that original boxes may
be included, but are not designed to withstand the rigors of shipping without additional protection.
Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not
responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request
is available at http://www.horizonhobby.com/content/service-center_render-service-center. If you
do not have internet access, please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling Horizon, you will be asked
to provide your complete name, street address, email address and phone number where you can
be reached during business hours. When sending product into Horizon, please include your RMA
number, a list of the included items, and a brief summary of the problem. A copy of your original
sales receipt must be included for warranty consideration. Be sure your name, address, and RMA
number are clearly written on the outside of the shipping carton.
Provided warranty conditions have been met, your Product will be serviced or replaced free of charge.
Service or replacement decisions are at the sole discretion of Horizon.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery,
please contact the appropriate Horizon Product Support office. Warranty Requirements - For
Warranty consideration, you must include your original sales receipt verifying the proof-of-
purchase date.
Non-Warranty Service
-
Should your service not be covered by warranty, service will be completed and payment will be
required without notification or estimate of the expense unless the expense exceeds 50% of the
retail purchase cost. By submitting the item for service you are agreeing to payment of the service
without notification. Service estimates are available upon request. You must include this request
with your item submitted for service. Non-warranty service estimates will be billed a minimum of
½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and
cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting
any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our
website http://www.horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and
ownership. If received, a non-compliant Product will not be serviced. Further, the sender will
be responsible for arranging return shipment of the un-serviced Product, through a carrier of
the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for
a period of 60 days from notification, after which it will be discarded.
EU Compliance Statement:
Horizon Hobby, LLC hereby declares that this product is
in compliance with the essential requirements and other relevant provisions of the EMC
Directive.
A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsi-
bility to dispose of their waste equipment by handing it over to a designated collections
point for the recycling of waste electrical and electronic equipment. The separate collec-
tion and recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household waste
disposal service or where you purchased the product.
5-14-2015
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ
.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
EXPOSURE
SHUTTER AUTO
BRIGHTNESS 050
AGC ----
DWDR OFF
RETURN
RET
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
MANUAL
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
BLC
SETUP
EXPOSURE
BACKLIGHT
BLC
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
WB MANUAL
COLOR TEMP
MANUAL
BLUE 045
RED 064
RETURN
RET
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
AUTO
DPC
LANGUAGE
ENGLISH
RESET
EXIT
IMAGE ADJ.
LENS SHAD.
ON
2DNR OFF
MIRROR OFF
FONT COLOR
CONTRAST 110
SHARPNESS
026
DISPLAY
LCD
NEG. IMAGE
OFF
RETURN
RET
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT COLOR
IMAGE ADJ.
DPC
LANGUAGE ENGLISH
RESET
EXIT
1234567890ABC
DEFGHIJKLMNOPQ
RSTUVWXYZ=/&:.
CLR
ALARM
SCENE
SYSTEM
PILOT
TIMER
VOLTAGE
HORIZON
EXIT
SPEKTRUM
:14.8V
:PERSONAL
:ON POS
:ON POS
:ON POS
:ON POS
:OFF POS
SETUP
EXPOSURE
BACKLIGHT OFF
WHITE BALANCE
ATW1
DAY&NIGHT AUTO
IMAGE ADJ.
DPC
LANGUAGE
ENGLISH
RESET
EXIT
D&N AUTO
D->N LEVEL
144
D->N DELAY
3 SEC
N->D LEVEL
112
N->D DELAY
1 SEC
RETURN
RET
D&N B/W
GAMMA 0.50
PED LEVEL
017
COLOR GAIN
176
RETURN
RET
BURST OFF
IR SMART
ON
IR LEVEL
HIGH
RETURN
RET
LENS SHAD.
LEVEL
020
LCD ADJUST
IR SMART
IRGAIN
066
HEIGHT 006
WIDTH 016
LEFT/RIGHT 001
TOP/BOTTOM 004
RETURN
RET
AREA SEL.
AREA1
AREA STATE
ON
GAIN 168
HEIGHT 005
WIDTH 005
LEFT/RIGHT 004
TOP/BOTTOM 004
RETURN
RET
HLC
LEVEL 200
RETURN
RET
FONT COLOR
LEVEL
003
ID & TITLE
003
Specifications
MODEL
SPMVC621
Image Sensor
1/3” Sony Super HAD II CCD
Horizontal Resolution
600TVL
Lens
2.1mm
Signal
NTSC
Input Voltage
DC 5V–36V
Integrated features
OSD, MIC
OSD Features
Voltage, Timer, Callsign
Minimum Illumination
0.01 Lux @1.2F
Day/Night
Color/Auto/B&W
Electronic Shutter Speed
1/60 –100,000
Dimensions
28.5mm x 26mm x 26mm
Power Consumption
60mA @ 5V, 140mAh @ 12V
Weight
14 grams
Recommended Video Transmitter
SPMVT1000, SPMVTM150
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential
harm when operating this product:
WARNING:
Procedures, which if not properly followed, create the probability of property damage,
collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION:
Procedures, which if not properly followed, create the probability of physical property
damage AND a possibility of serious injury.
NOTICE:
Procedures, which if not properly followed, create a possibility of physical property damage
AND a little or no possibility of injury.
WARNING:
Read the ENTIRE instruction manual to become familiar with the features of the
product before operating. Failure to operate the product correctly can result in damage to
the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and
requires some basic mechanical ability. Failure to operate this Product in a safe and responsible
manner could result in injury or damage to the product or other property. This product is not
intended for use by children without direct adult supervision. Do not attempt disassembly, use with
incompatible components or augment product in any way without the approval of Horizon Hobby,
LLC. This manual contains instructions for safety, operation and maintenance. It is essential to
read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in
order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
NOTICE:
This product is only intended for use with unmanned, hobby-grade, remote-controlled
vehicles and aircraft. Horizon Hobby disclaims all liability outside of the intended purpose and will not
provide warranty service related thereto.
WARRANTY REGISTRATION
Visit www.spektrumrc.com/registration today to register your product.
WARRANTY AND SERVICE CONTACT INFORMATION
Country of
Purchase
Horizon Hobby
Contact Information
Address
United States of
America
Horizon Service Center
(Repairs and Repair
Requests)
servicecenter.horizonhobby.
com/RequestForm/
4105 Fieldstone Rd
Champaign, Illinois, 61822
USA
Horizon Product Support
(Product Technical
Assistance)
productsupport@
horizonhobby.com.
877-504-0233
Sales
websales@horizonhobby.com
800-338-4639
EU
Horizon Technischer Service
service@horizonhobby.eu
Hanskampring 9
D 22885 Barsbüttel,
Germany
Sales: Horizon Hobby GmbH
+49 (0) 4121 2655 100
