Stevens AeroModel PuddleBug 2.4 User Manual Download | Manualshive

Page: 1 / 12

background image

PuddleBug

Micro RC Model for Spektrum / ParkZone 2.4 systems

Length 10.5 inches | Span 17.75 inches | Wing Area 71 inches

2

| Flying Weight 1.1 oz.

Version 01/06/2010

PuddleBug © 2010 Stevens AeroModel all rights reserved.

Page 1 of 13

2.4

1
2
3
...
»

Summary of Contents for PuddleBug 2.4













Reviews:

No comments

Related manuals for PuddleBug 2.4

Brand: Laser Pegs Pages: 2

Brand: Parkside Pages: 40

Brand: LEGO Pages: 176

Mini Dual Deploy Screech

Brand: Madcow Rocketry Pages: 3

Sit-to-Stand Learning Walker

Brand: VTech Pages: 16

Brand: Matchbox Pages: 2

midnight gambler 21005

Brand: GRAUPNER Pages: 40

Brand: PARKZONE Pages: 24

Brand: Black Horse Model Pages: 30

Brand: TILLIG BAHN Pages: 3

Brand: Trix Pages: 36

Brand: Hacker Pages: 13

L-19/0-1 BIRD DOG 1730mm Wingspan

Brand: Radio control model Pages: 32

Brand: Skymaster Pages: 14

4-8-4 Northern Steam Locomotive and Tender

Brand: Lionel Pages: 12

Brand: WattAge Pages: 20

Showcase Line EMD NW-2

Brand: S-Helper Service Pages: 24

Brand: Hotbodies Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands