STI PR-7505 Manual Download | Manualshive

Page: 1 / 16

background image

Product May Vary Slightly From Picture.

v. VII

Owners

’ Manual

Exercise can present a
health risk. Consult a
physician before beginning
any exercise program with
this equipment.

If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed.

Keep children and pets away
from equipment when in use.
Always make sure all bolts
and nuts are tightened prior
to each use. Follow all safety
instructions in this manual.

WARNING

CAUTION:

Weight on this product should not exceed 181 kgs/ 400 lbs

MADE IN TAIWAN

1
2
3
...
»

Summary of Contents for PR-7505

















Reviews:

No comments

Related manuals for PR-7505

Brand: CARDIO STRONG Pages: 52

Elliptical FE46

Brand: Fuel Fitness Pages: 22

Resolute RSL 324

Brand: Precor Pages: 12

Resolute RSL 208

Brand: Precor Pages: 12

Brand: Kettler Pages: 24

Satura P 07653-000

Brand: Kettler Pages: 28

Brand: Kettler Pages: 48

Brand: CycleOps Pages: 44

Brand: BH FITNESS Pages: 23

Brand: BH FITNESS Pages: 33

Brand: BH FITNESS Pages: 37

Brand: Diamondback Pages: 56

Brand: CUP?S Pages: 20

PRO-FORM 16.0 MME

Brand: ICON Health & Fitness Pages: 36

Brand: Dyaco Pages: 34

Brand: BH FITNESS Pages: 23

Brand: Nautilus Pages: 56

Brand: THERA-Trainer Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands