background image

Installation and Operation Instructions

Superior™ Indoor Wood Burning Fireplace

P/N 126601-01   Rev. A   02/2014

Models

WRT4536RS
WRT4536RH

WRT4536WS
WRT4536WH

WRT4542RS
WRT4542RH

WRT4542WS
WRT4542WH

WRT4550RS
WRT4550RH

WRT4550WS
WRT4550WH

P126601-01

SAVE THIS BOOK

This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also contains 

information that will enable you to obtain replacement parts or accessory items when needed. Keep it with your other 

important papers.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.

This wood burning fireplace complies with  

UL127 CAN/ULC-S610-M87 standard as a 

FACTORY BUILT FIREPLACE.

Ce foyer au bois est conforme aux UL 127 CAN/ULC-

S610-M87 norme comme une USINE CONSTRUITE 

CHEMINÉE.

This fireplace is approved for use as a wood burning fireplace or for use with a vented gas log approved to  

ANSI Z21.60 or Z21.84 standards or for use with a vent-free gas log heater approved to ANSI Z21.11.2 standard.

FOR CANADA: The authority having jurisdiction 

(such as the municipal building department, fire 

department, etc.) should be contacted before 

installation to determine the need to obtain a 

permit.

POUR LE CANADA: L’autorité compétente (comme le 

service municipal du bâtiment, les pompiers, etc.) doit 

être contacté avant l’installation afin de déterminer la 

nécessité d’obtenir un permis.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)  

or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated 

on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

WARNING: If the information in these 

instructions is not followed exactly, a fire or 

explosion may result causing property damage, 

personal injury or death.

AVERTISSEMENT : Assurez-vous de bien suivre les 

instructions données dans cette notice pour réduire au 

minimum le risque d’incindie ou d’explosion ou pour éviter 

tout dommage matériel, toute blessure ou la mort.

 

—  Do not store or use gasoline or other 

flammable vapors and liquids in the vicinity 

of this or any other appliance.

 

—  WHAT TO DO IF YOU SMELL GAS: 

•   Do not try to light any appliance. 

•   Do not touch any electrical switch; do not 

use any phone in your building. 

•   Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 

supplier’s instructions. 

•  If you cannot reach your gas supplier, call 

the fire department.

 

— Installation and service must be performed 

by a qualified installer, service agency or the 

gas supplier.

 

—  Ne pas entreposer ni utilizer d’essence ni d’autres 

vapeurs ou liquides inflammables dans le voisinage 

de cet appareil ou de tout autre appareil.

 

—  QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ : 

•   Ne pas tenter d’allumer d’appareil.

•  Ne touchez à aucan interrupteur. Ne pas vous 

servir des téléphones se trouvant dans le bâtiment 

où vous trouvez.

•  Appelez immédiatement votre fournisseur de 

gaz depuis un voisin. Suivez les instructions du 

fournisseur.

•  Si vous ne pouvez rejoindre le fournisseur de gaz, 

appelez le service des incindies.

 

— L’installation et l’entretien doivent être assurés par un 

installateur ou un service d’entretien qualifié ou par 

le fournisseur de gaz.

Summary of Contents for WRT4536RH





























Reviews: