background image

 

© 

Copyright (2021) 

All

 rights reserved. Changes, which serve technical improvements are reserved.

 

 

PRSU Series, Operating Instructions Manual (Revision 1.0) 

 

TAPESWITCH CORP. 

100 Schmitt Boulevard 
Farmingdale 
New York 11735 
Phone: 800-234-8273  
Fax: 631-630-0454 
info@tapeswitch.com 
www.tapeswitch.com

 

 

 

 

 

 

 
 
Introduction

 

 
 
This operating instruction shall familiarize you with the

 

safety relay controller 

models: PRSU/2, PRSU/4 and PRSU/5. 

 

Target Audience

 

These operating instructions are addressed to the following personnel: 
 

 

Skilled personnel who plan or develop safety equipment for machines 
and plants, who are familiar with the safety instructions and safety 

 

regulations.

 

 

 

Skilled personnel who build, install, maintain and operate safety 

 

equipment in plants and machinery.

 

Symbol Key 
 

These operating instructions contain several symbols which are used to  
highlight important information: 
 
 

 

This symbol indicates text passages which 

must absolutely be paid attention 

to.

 Disregarding may lead to serious personal injury or damage to property. 

 

 

 
This symbol indicates text passages which contain important information. 
 

 

 
This sign is used to indicate actions by the installer or operator. 
 
 

 

This sign illustrates that a condition has changed after an action has been 
carried out. 
 
 

 

 

 

PRSU/2, PRSU/4, PRSU/5 

 

Operating Instructions Manual 

 

Safety controllers for safety mats and  

sensing edge products 

Summary of Contents for PRSU/2















Reviews: