background image

©Copyright Task Force Tips, Inc. 2002-2018 

LIX-030 January 8, 2018 Rev24

MANUAL: CROSSFIRE

®

 Monitor

INSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE

DANGER

Understand manual before use. Operation of this device without understanding the manual and 
receiving  proper  training  is  a  misuse  of  this  equipment.  Obtain  safety  information  at  www.tft 
com/serial-number.

DANGER

Risk of sliding increases at low elevation angles. To reduce risk of injury or death from sliding, 
do not pull elevation pin stop while on portable base.

This Instruction Manual is intended to familiarize fi refi ghters and maintenance personnel with the operation, servicing, and 
safety procedures associated with the portable monitor.
This manual should be kept available to all operating and maintenance personnel.

TASK FORCE TIPS, LLC.

MADE IN USA • www.tft.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

        800-348-2686

DAN

GER

Additional Copies A

vailable 24-hours

and Safety Instructions Befor

e Use.

Read and Understand All Operation

This Stop (pin pulled) Is Danger

ous.

Operating On P

ortable Base Below

FOG

STREAM

 See Section 4.10.5

For Flow/Pressure

Operating Envelope

Summary of Contents for SAFE-TAK 1250





















Reviews: