INSTALLATION INSTRUCTIONS
3
FAUCET INSTALLATION
A)
Remove old faucet. Clean sink surface in preparation for new faucet. Before installation,
remove the quick connector (1) from the counterclockwise direction. Unscrew the nut (2),
and remove the washers (3 & 4). If installing the faucet assembly without the escutcheon,
begin with step B. If installing the faucet with the escutcheon, begin with step 3.
B) OPTIONAL FLANGE INSTALLATION. Before installation, ensure that the flange (1) is placed
on the bottom of the new faucet assembly. Insert the faucet body through the hole in the
sink. Install the rubber washer (2), metal washer (3) onto the threaded mounting shank.
Thread nut (4) onto mounting shank. Do not overtighten.
C) OPTIONAL ESCUTCHEON INSTALLATION. Before installation, remove the flange (1). Apply a
bead of plumber’s putty or silicone caulk around the faucet openings. Install the gasket over
the three holes in your sink.
D) OPTIONAL ESCUTCHEON INSTALLATION. Insert the faucet body through the hole in the
gasket. Install the rubber washer (1), metal washer (2) onto the threaded mounting shank.
Thread nut (3) onto mounting shank. Do not overtighten.
E) After inserting the hose through the hole in the sink surface, reattach the quick connector
(1) by screwing it onto the threaded end of the hose (2) in a clockwise motion. Hand tighten
only.
F) Align block (1) and tabs on quick connect. Push quick connect housing firmly upward and
snap onto receiving block. Pull down moderately to ensure connection has been made. If
it is necessary to remove quick connect, squeeze tabs on hose between index finger and
thumb, then pull down to disconnect. After connecting the hose, install the weights (2) at
the bottom of the hose to ensure ease of function.
TURN OFF
TURN OFF
SI
LI
CO
NE
Your installation may require new supply
lines. (Supply lines are not included.)
CUSTOMER SERVICE
WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
WITH OPTIONAL ESCUTCHEON
Do not, use plumber’ putty on cultured marble or other
composite sinks. Putty will discolor the sink.
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
THANK YOU
FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers
Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench
Silicone caulk
6
7
EXPLODED DIAGRAM FOR REFERENCE
MAINTENANCE
Your new faucet is designed for years of trouble-free performance. Keep
it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel
wool and harsh chemicals as these will dull the finish and void your warranty.
2
TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply
valves. These are usually found under the sink.
WARNING: READ ALL
the instructions completely before beginning.
READ ALL
warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help?
Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
06-8834S
SINGLE HANDLE KITCHEN FAUCET
ADJUSTING SPRAY SETTINGS
By rotating the spray head end to the point you hear a click, you can alternate
between stream or spray function as desired.
5
FLUSHING THE WATER LINES
Pull the hose assembly out of the spout and remove the spray head by unscrewing
it from the hose in a counterclockwise direction. Be sure to hold the end of the hose
down into the sink and turn the faucet on to the warm postion where it mixes hot and
cold water. Flush the water lines for one minute. This flushes away any debris that
could cause damage to internal parts. Check for leaks. Re-tighten any connections
if necessary, but
do not overtighten
. Reinstall the spray hose. Note: Do not lose the
gasked (1) in the hose.
1
2
1
A
B
C
D
E
F
1
2
3
4
2
1
3
4
3
2
1
1
2
4
ATTACH THE HOT AND COLD SUPPLY LINES
Make connections to water lines. Use 1/2” I.P.S. faucet connections (2) or use supplied coupling nuts
(3) with 3/8” O.D. ball-nose riser (1). Use two wrenches when tightening. Do not over tighten.
2
3
1
1
1 - SPRAY HEAD
2 - INVERTER
3 - SPOUT
4 - WEARABLE RING
5 - SPOUT NUT
6 - O-RING
7 - CLIP
8 - O-RING
9 - BODY
10 - CARTRIDGE
11 - BONNET
12 - CAP
13 - HANDLE
14 - BOLT
15 - HANDLE SEAT
16 - SCREW
17 - INDEX
18 - CONNECTOR
19 - HOSE
20 - HOSE
21 - BLOCK
22 - O-RING
23 - COUPLING NUT
24 - WEIGHT
25 - NUT
27 - WASHER
26 - WASHER
28 - SHANK
29 - FLANGE
30 - WASHER
31 - BASE PLATE
32 - ESCUTCHEON
