background image

A

B

C

D

E

F

INSTALLATION INSTRUCTIONS

 

CUSTOMER SERVICE      WEST 1-800-267-4774   |   EAST 1-800-387-7064   |   taymor.com

® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.

A

B

TURN OFF

TURN OFF

4

A

B

D

C

B

E

F

A

A

F

G

H

SIL

IC

ON

E

B

SI

LI

CO

NE

I

J

H

E

C

D

THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:

cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT

1 - O-RING

2 - HANDLE

3 - HANDLE SEAT

4 - HANDLE SCREW

5 - SLEEVE

6 - RETAINER NUT

7 - WASHER

8 - CARTRIDGE

9 - SEAT

10 - SPRING

11 - SCREW

12 - BASE PLATE

13 - MOUNTING NUT

15 - AERATOR

16 - POP-UP

17 - LIFT ROD

19 - WASHER

20 - NUT

21 - SPRING 

       CLIP

22 - BALL ROD

23 - LIFT

       STRAP

18 - FLANGE

C

14 - COUPLING NUT

EXPLODED DIAGRAM FOR REFERENCE 

MAINTENANCE

 Your new faucet is designed for years of trouble-free performance. Keep it looking 

new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh 
chemicals as these will dull the finish and void your warranty.

THANK YOU

 FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE  CAREFULLY 

ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.

HAVE BASIC TOOLS READY

RECOMMENDED TOOLS:

1

Flashlight

Teflon tape Screwdrivers

Adjustable

 wrench and

pipe wrench

Plumber’s putty

Safety goggles

Torque wrench

Silicone caulk

5

6

INSTALLING POP-UP DRAIN

A)

 Remove pop-up plunger (A) and flange (B). Screw locknut (C) all the way down. Push 

gasket (D) down. Apply silicone to underside of flange (B).

B) 

Insert body into sink (from underneath). Screw flange onto body. Pivot hole (E) must face    

  the back of the sink.

C)

 Tighten locknut (C) and gasket (D) but do not overtighten. Remove pivot ball retaining nut 

(E).

D) 

Slide pivot rod (F) into the eye of the pop-up plunger (A). Hand tighten retaining nut.

E)

 Slide pivot rod (F) through hole in spring clip (G), then through lever strap (H) and back  

 

  through spring clip (G)

.

 

F)

 Insert lift rod (I) down through faucet body and then into lever strap (H). Tighten screw (J).   

  Connect assembly to drain.

7

8

HAND TIGHTEN THE MOUNTING NUTS

From underneath the sink, hand tighten the mounting nuts. Tighten gently until snug and alternate from 
side to side to seat the faucet body evenly.

Don’t over tighten

FLUSHING & AERATOR CLEANING

Remove the aerator by turning it counterclockwise. Remove the internal
parts of the aerator by pushing them out with your fingers. Remove any
debris. Turn on hot and cold water supplies. Turn faucet handles all the
way on and run water through the spout for about a minute to remove
debris. While water is running check all connections for leaks.
Reassemble the aerator and screw it back into the spout hand tight.

3

GASKET & FAUCET INSTALLATION

A)

 Apply a bead of plumber’s putty or silicone caulk around the sink openings.

B)

 Install the gasket over the three holes in your sink.

C) 

Install faucet shanks through the holes of the sink. Centre the faucet body on the sink.

Don’t use plumber’s putty on cultured marble or other composite sinks. 
Putty will discolour the sink.

2

TURN OFF THE MAIN WATER SUPPLY

Locate water supply inlets and shut off water supply valves. These are usually found under 
the sink.

WARNING: READ ALL

 the instructions completely before beginning.  

READ ALL

 warnings, care and maintenance information.

Taymor recommends calling a professional if you are uncertain about installing this product!

This product should be installed in accordance with all local and provincial plumbing and building codes.

Need Help?

 Please call our toll-free Customer Support line at 

(WEST) 1-800-267-4774     (EAST ) 1-800-387-7064 for additional assistance or service.

CALEDONIA 06-4670PCHL / 06-4670PSNL / 06-4670BRNL

TWO HANDLE LAVATORY FAUCET

Your installation may require new supply 
lines. (Supply lines are not included.)

MAKE CONNECTIONS TO WATER LINES

Use 1/2” IPS faucet connections (1) and tighten connections with wrench. Or use the supplied plastic 
coupling nuts (3) with 3/8” O.D. ball-nose risers (2), hand tighten only. Do not overtighten. Do not use 
metal coupling nuts (4). Do not use plumber’s putty, pipe dope, or any other type of sealing com-
pound on water inlet or threads. Additional compound is not necessary.

2

3

1

4

Reviews: