background image

R

2800 LAURA LANE • MIDDLETON, WI 53562 • (800) 288-9383 • FAX (608) 836-9044 • www.tcsbasys.com

1

SZ1041A

Make Up Air Unit Thermostat

Product Manual           

Description                              

The SZ1041A is a microprocessor-based programmable 

thermostat designed to control   air  handling units and 

make up air units with modulating economizers and/or 

modulating heating or cooling. The SZ1041A has a 365-

day time clock.

Features                                 

•  Stand-alone or network operation

•  Outdoor air sensor input with heating & cooling lockout

•  Adjustable delay on power-up and start-up for  

soft starts

•  P+I control option on digital stages

•  Smart Recovery

•  No battery backup required

•  Built-in HVAC equipment protection

•  32 character LCD display

•  Six status LEDs for monitoring  

•  Remote room sensing capability

•  User setpoint adjustment limits

•  Local and remote override capability 

•  System and fan switching with access lockouts  

•  Equipment monitoring inputs and indication

•  External time clock input 

•  Access to programming or schedule may be locked 

out or limited with the use of an access code

•  Fahrenheit or Celsius temperature display

Contents                                 

Description

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Mounting 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Wiring

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Setup

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Programming

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Setting Clock & Schedule

. . . . . . . . . . . . . . . . . . . . . . . 8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Checkout & Troubleshooting

  . . . . . . . . . . . . . . . . . . . . 12

LED Description

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Limiting Occupant Access  . . . . . . . . . . . . . . . . . . . . . . 15

User’s Guide

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Mounting                                

The SZ1041A is designed for wall mounting using 

two #6 sheet metal screws, either over a horizontally 

installed 2" x 4" junction box, or directly to block or dry-

wall. 

For best results, the thermostat should be mounted on 

an interior wall which reflects normal room environment, 

at a height of approximately five feet from the floor. 

Avoid areas exposed to direct sunlight, unusual heat 

or cool sources, open doors and windows, unventilated 

locations and hot or cold air from diffusers.
If using a remote room sensor, it should be mounted in 

the manner described above. The thermostat may then 

be mounted in an area which is accessible for adjusting 

its settings. 

Caution

: Remove power from thermostat prior to 

mounting.

        Communicating Thermostats

Summary of Contents for SZ1041A
















Reviews: