background image

Information 

Brochure

Choose controls

to match

application

1

Application 

Brochure

Design your 

mechanical 

applications

2

Rough In

Wiring

Rough-in

wiring 

instructions

3

Wiring

Brochure

Wiring and 

installation of 

specific control

4

Data

Brochure

Control settings 

and sequence of 

operation

5

Job

Record

Record settings & 

wiring details for 

future reference

6

D 480 

06/06

tekmarNet

®

4 User Switch 480

- Data Brochure

 

1 of 8 

© 2006 

 D 480 - 06/06

Introduction

The User Switch 480 has 3 programmable buttons that allow users to easily change the operating scene or allow users to 
enable / disable tN4 setpoint devices on a tN4 system.

Multiple User Switches are required if more than 3 scenes or setpoint enable / disables are desired.

The 480 has 3 demand inputs that allow for connection of a tN4 system to a third party automation system or telephone 
switch. This allows users to remotely change the operating scene on a tN4 system.

Features

• 

• 

tN4 Compatible

• 

• 

3 User buttons

• 

• 

3 Demand Inputs

- Input for Home or Building Automation

- Input for Telephone Switch

- Input for Security Systems

User

Button

1

User

Button

2

User

Button

3

Decora cover plate not included

Summary of Contents for tekmarNet4 User Switch 480









Reviews: