background image

INSTALLATION MANUAL

Page 1        of  12  

            Manual #  0550001-687

Revision 1 

 

INSTALLATION AND OPERATION OF MV-3 SERIES

SIDE MOUNT CONTROL

OWNER’S MANUAL

For Single Station Only

These “saftey alerts” alone cannot elim-
inate  the hazards they signal. 

Strict 

compliance to these special instruc-
tions

 

when installing, operating or 

performing maintanence and using 
common sence are the most effective 
accident prevention measures.

Hazards or unsafe practices 

which COULD result in sever 

personel injury or death.

WARNING

!

NOTICE

Throughout this manual,    Warnings and Cautions,  accompa-

nied by the International Hazard Symbol         , are used to alert the manufacturer or installer to special 
instructions concerning a particular service or operation that may be hazardous if preformed incor-
rectly or carelessly.

Warnings alone do not eliminate dangers, nor are the a substitute for safe boat handling and proper 
accident prevention measures.  

Observe these alerts carefully!

!

DANGER

!

Immediate Hazards which

WILL result in severe

personel injury or death.

Hazards or unsafe practices 

which COULD result in  injury, 

product and/or property 

damage.

CAUTION

!

NOTICE

Information that is important to 

the proper installation, 

operation and maintenance, but 

is not hazard related.

INSTALLER: THESE INSTRUCTIONS CONTAIN IMPORTANT SAFETY INFORMATION AND MUST BE FORWARDED TO THE BOAT OWNER

.

Summary of Contents for MV-3 Series









Reviews: