background image

 

Zonda 8EP Instructions 

Thank you for buying a Wild Country Zonda 8EP tent and we hope you have fun using it. Please read 
these instructions carefully before you pitch your tent for the first time and keep them in a safe 
place for future reference. If used correctly and with care your tent should give you years of trouble 
free use. Top Tip - We would recommend that you take out insurance against storm and accidental 
damage as these are not covered by the guarantee.
 

The first time you use the tent 

If possible we would recommend that you do a practice pitch before heading off on your camping 
holiday for the first time. This will give you the opportunity to learn the best way to pitch and then 
pack away your tent and also check that all the component parts are there. Top Tip – don’t forget to 
take the pegs and pump with you! 

Please also consider the weather conditions before using the tent. This tent is designed to be used in 
moderate wind and weather conditions so either do not pitch the tent or take it down in strong 
winds or adverse weather such as hail or snowfall.  Please note this tent is not designed for or 
guaranteed for long term, static or commercial use.  

Condensation and ventilation – what you need to know before you go 

Your tent is constructed using an impermeable waterproof PU coated outer fabric that has factory 
taped waterproof seams. It also has various vents and mesh panels that aid air circulation and these 
should be kept clear and left open for maximum effect. However in many conditions and especially if 
there is little wind then condensation will be noticeable inside the tent. This can actually run or drip 
down onto the groundsheet and can create pools of water. This is not due to leakage through the 
fabric or seams but simply from the warm moist air inside the tent (caused by the occupants) 
condensing against the cooler impermeable waterproof coating of the outer tent fabric. Top Tip 
The condensation can be quite extreme at times so we would recommend taking a quick drying 
absorbent cloth to mop up any excess water.
  

Where to pitch 

If possible find a level area and ideally one that is protected from the wind. Keep in mind that it is 
best to face the main door away from the prevailing wind direction so pitch the back of the tent into 
the wind if you can. Avoid pitching under trees because tree sap is extremely sticky and difficult to 
clean off and even a small falling branch can damage your tent. Clear the chosen area of any lose 
objects and pay particular attention to remove anything sharp to prevent damage to the built in 
groundsheet.  

Summary of Contents for Wild Country Zonda 8EP










Reviews: