background image

       

          

    

SLOS289E − DECEMBER 1999 − REVISED SEPTEMBER 2006

1

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

D

High Output Drive . . . >300 mA

D

Rail-To-Rail Output

D

Unity-Gain Bandwidth . . . 2.7 MHz

D

Slew Rate . . . 1.5 V/

µ

s

D

Supply Current . . . 700 

µ

A/Per Channel

D

Supply Voltage Range . . . 2.5 V to 6 V

D

Specified Temperature Range:
−  T

A

 = 0

°

C to 70

°

C . . . Commercial Grade

−  T

A

 = −40

°

C to 125

°

C . . . Industrial Grade

D

Universal OpAmp EVM

     

description

The TLV411x single supply operational amplifiers provide output currents in excess of 300 mA at 5 V. This
enables standard pin-out amplifiers to be used as high current buffers or in coil driver applications. The TLV4110
and TLV4113 come with a shutdown feature.

The TLV411x is available in the ultra small MSOP PowerPAD

 package, which offers the exceptional thermal

impedance required for amplifiers delivering high current levels.

All TLV411x devices are offered in PDIP, SOIC (single and dual) and MSOP PowerPAD (dual).

FAMILY PACKAGE TABLE

DEVICE

NUMBER OF

PACKAGE TYPES

SHUTDOWN

UNIVERSAL

DEVICE

NUMBER OF

CHANNELS

MSOP

PDIP

SOIC

SHUTDOWN

UNIVERSAL

EVM BOARD

TLV4110

1

8

8

8

Yes

Refer to the EVM

TLV4111

1

8

8

8

Refer to the EVM

Selection Guide

TLV4112

2

8

8

8

Selection Guide

(Lit# SLOU060)

TLV4113

2

10

14

14

Yes

(Lit# SLOU060)

HIGH-LEVEL OUTPUT VOLTAGE

vs

HIGH-LEVEL OUTPUT CURRENT

VDD = 3 V

IOH − High-Level Output Current − mA

V

OH

− High-Level Output V

oltage − V

TA = 70

°

C

TA = 25

°

C

TA = 0

°

C

TA = −40

°

C

3.0

2.9

2.8

2.7

2.6

2.5

2.4

2.3

2.0

0

50

200

100

150

250

300

2.2

2.1

TA = 125

°

C

TA = −40

°

C

LOW-LEVEL OUTPUT VOLTAGE

vs

LOW-LEVEL OUTPUT CURRENT

VDD = 3 V

IOL − Low-Level Output Current − mA

TA = 70

°

C

TA = 25

°

C

TA = 0

°

C

OL

V

 Low-Level Output V

oltage − V

1.0

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.0

0

50

200

100

150

250

300

0.2

0.1

TA = 125

°

C

Copyright 

 1999−2006, Texas Instruments Incorporated

    !"#  $  %&'#  "$    (&)*%"#  +"#',

+&%#$  %!  #  $('%%"#$  ('  #-'  #'!$    '."$  $#&!'#$

$#"+"+  /""#0,  +&%#  (%'$$1  +'$  #  '%'$$"*0  %*&+'

#'$#1    "**  (""!'#'$,

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

1

2

3

4

8

7

6

5

1OUT

1IN −

1IN +

GND

V

DD

2OUT
2IN −
2IN+

TLV4112

D, DGN, OR P PACKAGE

(TOP VIEW)

Operational Amplifier

+

PowerPAD is a trademark of Texas Instruments. All other trademarks are the property of their respective owners.

Summary of Contents for TLV4110




































Reviews: