background image

1

SLUUBM0 – May 2017

Submit Documentation Feedback

Copyright © 2017, Texas Instruments Incorporated

TPS92518EVM Dual Buck Controller Evaluation Module

User's Guide

SLUUBM0 – May 2017

TPS92518EVM Dual Buck Controller Evaluation Module

This user's guide describes the specifications, board connection description, characteristics, operation,
and use of the combined, two board TPS92518 Evaluation Module (EVM). A complete schematic diagram,
printed circuit board layouts, and bill of materials are included in this document.

Contents

1

Description

....................................................................................................................

2

2

Performance Specifications

................................................................................................

3

3

Performance Data and Typical Characteristic Curves

..................................................................

4

4

Schematic, PCB Layout, and Bill of Materials

..........................................................................

11

5

Software

.....................................................................................................................

16

6

Use of LEDSPIMCUEVM-879 Microcontroller Board for SPI Communications with the TPS92518

............

22

List of Figures

1

Frequency vs Output Voltage

..............................................................................................

4

2

Efficiency Over Temperature at Different Peak Threshold Settings

..................................................

4

3

PWM Dimming, Multiple PWM Frequencies, Both Channels

..........................................................

5

4

Single-Channel PWM Dimming at 400 Hz

...............................................................................

5

5

SPI Setting Output Enable Bit and Subsequent Switching Initiation

..................................................

6

6

Hardware PWM Enable Pulled High, Triggering Switching

............................................................

6

7

SPI Clearing Output Enable Bit and Subsequent Switching Shutdown

..............................................

7

8

Hardware PWM Enable Pulled Low, Triggering Chip Shutdown

......................................................

7

9

Current Sharing

..............................................................................................................

8

10

Switch Node Current

........................................................................................................

8

11

Switch Node Current

........................................................................................................

9

12

Additional Circuitry Required for Shunt FET Dimming

...............................................................

10

13

TPS92518EVM-878 Schematic

..........................................................................................

11

14

TPS92518EVM-878 Top Side

............................................................................................

12

15

TPS92518EVM-878 Bottom Side

........................................................................................

13

16

Setup Screen 1

.............................................................................................................

16

17

Setup Screen 2

.............................................................................................................

16

18

Setup Screen 3

.............................................................................................................

17

19

Setup Screen 4

.............................................................................................................

17

20

Setup Screen 5

.............................................................................................................

18

21

Setup Screen 6

.............................................................................................................

18

22

Setup Screen 7

.............................................................................................................

19

23

Setup Screen 8

.............................................................................................................

19

24

Setup Screen 9

.............................................................................................................

20

25

Setup Screen 10

...........................................................................................................

20

26

Setup Screen 11

...........................................................................................................

20

27

LEDSPIMCUEVM-879 Schematic, Page 1

.............................................................................

22

28

LEDSPIMCUEVM-879 Schematic, Page 2

.............................................................................

23

29

LEDSPIMCUEVM-879 Schematic, Page 3

.............................................................................

24

Summary of Contents for TPS92518EVM































Reviews: