background image

Professional 75lb Dual Impeller 

Broadcast Spreader

MODEL #DI2020

ASSEMBLY INSTRUCTIONS

P80000_M52098_Rev_June2020

Professional 75lb Dual Impeller 

Broadcast Spreader

MODEL #DI2020

ASSEMBLY INSTRUCTIONS

PAGE 1

Thank you!

IN THE BOX

You have purchased the highest quality professional 

broadcast spreader on the market.  Featuring an 

advanced design duel impeller system. This spreader 

provides a symmetrical spread pattern, eliminating the 

potential for uneven application. The dual impeller design 

provides superior flexibility in spreading a variety of 

granule types and seeds. A single adjustment of the rate 

plate is all that is required to deliver a uniform application 

each time.

While your spreader is mostly assembled, to minimize 

shipping costs, you will need to attach the tires, frame 

rest, upper handle, and control rods. 

Before you begin, you will need the following tools to 

assemble your DI2020 spreader:

Two 7/16” box wrenches,

One 1/2”

One 3/8” box wrench

(2) Control Rods

Helpful Hints 

(1) Deflector

Control

Rod

(2) Tires

P15043

(1) Frame Rest

79008

(1) Upper Handle

Assembly

60368

(1) Hopper 

Frame 

Assembly

Other Items:

(1) Rain cover

(1) Hopper screen

(1) Hardware pack

The hardware kit include additional spare hardware:

- Cotter pin (for retaining tire)

- (2) 2 ¼” stainless bolts 

- (2) ¼” stainless nuts

Summary of Contents for DI2020












Reviews: