background image

Warning! This model is not a toy.

It is designed for maximum performance.  Please seek advice if one is not familiar with this kind

of engine powered precision model.  Operating this model without prior preparation may cause

injuries.  Remember, safety is the most important thing.  Always keep this instruction manual at

hand for quick reference.      

PRECISION LASER CUT

EASY BUILT KIT SERIES

 MADE IN CHINA

T he  Wor ld M ode ls

M a nufa c t uring Co., Lt d.

w w w. t h e w o r l d m o d e l s . c o m

INSTRUCTION MANUAL

Wing Span               :      72 in / 1830 mm

Wing Area                :      736 sq in / 47.5 sq dm

Flying Weight           :      6.6 lbs / 3000 g

Fuselage Length      :      48 in / 1220 mm

Requires 

           : 

[ A335 Kit ]

[ A335 Kit ]

*Specifications are subject to change without notice.*

1/6 PA-25 PAWNEE

1/6 PA-25 PAWNEE

"Glow Power" requires: 6-channel radio w/4 mini servos, 
3 standard servos, 2-stroke 0.40-0.46 engine.
"Electric Power" requires: 6-channel radio w/6 mini 
servos, Outrunner Motor KM37490750 w/Radial Mount 
Adaptor HW2340300, 40A Brushless ESC, 4 cells 14.8V 
3200mAh Lipo battery and charger.

Summary of Contents for 1/6 PIPER PA-25 PAWNEE





















Reviews: