background image

Owner’s Manual   —   Phoenix Axial Air Mover

Installation, Operation & Service Instructions

www.thermastor.com • sales@thermastor.com

Toll-Free -800-533-7533

Read and Save These Instructions

Phoenix Axial Air Mover

TS-285

The Phoenix Axial Air Mover is the industry’s only Air Mover specifically engineered with patent pending 
FOCUS

TM

 Technology. FOCUS

TM

 Technology revolutionizes evaporative drying by producing air velocities 

greater than competitive product offerings. This highly focused air flow is directed towards the restoration 
industry’s problematic drying areas namely, carpet and pad, sub-floor, sill plate and walls. No other fan 
dries the sill plate as quickly! Finally, the Phoenix Axial Air Mover with FOCUS

TM

 Technology sustains these 

air velocities further than any other Axial Air Mover.  
The Phoenix Axial Air Mover includes a 2-speed motor delivering a focused 
airstream of approximately 3000 cfm, lightweight stackable 
enclosure designed to fit existing vehicle rigging, on-board duplex 
GFCI outlet, circuit breaker, superior cord management and hour 
meter. 
Conventional air movers create a circular air jet. With a circular 
air jet the only way to get air into the square corner is to point 
the fan towards the corner. This angle toward the wall wastes 
valuable air velocity and throw distance. FOCUS

TM

 Technology 

creates an air jet with a square corner, resulting in optimized 
drying ability. In addition, the Axial Air Mover features built in 
4.5° positioning which increases the fans ability to dry.
Dry fast, smart and profitably with Phoenix.

 Phoenix Axial Air Mover

•  Approximately 3000 CFM air flow directed where 

you need it. 

•  Operator interface conveniently located for easy 

access, featuring: power indicator lamp, large three-
position switch, circuit breaker, GFCI outlet, and 
hour meter.

•  Daisy-chain up to four Phoenix Axial Air Movers on a 

single circuit. 

•  Integral circuit breaker eliminates nuisance trips to 

the breaker box.

•  Axial Air Mover itself is also GFCI protected.
•  Units interlock for ease of stacking during storage 

and handling.

•  Weighs 2.5 lbs less than competitive units.
•  Linear low density polyethylene construction.
•  Low bearing temperatures increase motor life.
•  Permawick®, low maintenance, long life lubrication.

Specifications subject to change without notice.

Revised 1/07

Phoenix Axial Air Mover
PN 4025200

PO Box 8680 • Madison, WI 53708

Summary of Contents for Phoenix TS-285










Reviews: