background image

NanoCam3D Mk.1 Instruction Manual

IMPORTANT – READ CAREFULLY BEFORE USE

KEEP FOR FUTURE REFERENCE

Contents

 1 Introduction and Designated Use.................................................................................................3

 1.1 Safety Instructions................................................................................................................4
 1.2 Quick Start Guide..................................................................................................................4

 2 Optional Camera Setup................................................................................................................4

 2.1 Control Elements..................................................................................................................5
 2.2 Video Norm Setup.................................................................................................................5
 2.3 3D Video Mode Setup...........................................................................................................5
 2.4 Reset to Factory Default Settings.........................................................................................6
 2.5 Sensor Vertical Adjustment...................................................................................................6
 2.6 Side-by-Side Offset Adjustment............................................................................................7
 2.7 Auto Exposure Adjustments..................................................................................................8

 3 Warranty....................................................................................................................................... 9
 4 Disposal and Environmental Protection........................................................................................9
 5 Manufacturer Information and Technical Support.........................................................................9
 6 Regulatory Notes........................................................................................................................ 10

 6.1 United States of America....................................................................................................10
 6.2 Canada............................................................................................................................... 10
 6.3 European Union..................................................................................................................11

List of Figures

Figure 1: Camera front and rear side................................................................................................3
Figure 2: Control Elements...............................................................................................................5
Figure 3: Vertically misaligned images (left) and correctly aligned images (right).............................6
Figure 4: Side-by-Side offset positions: to the left, center, to the right..............................................7

List of Abbreviations

AE

Auto Exposure

ESD

Electrostatic Discharge

FS

Field-Sequential

CVBS

Color Video Blanking Signal

FPV

First Person View

SBS

Side-by-Side

SELV

Separated/Safety Extra Low Voltage

Page 1 of 12

Subject to change without notice.

EN

Summary of Contents for NanoCam3D Mk.1













Reviews: