background image

PROGRAM TIMER

WARNING :  (For U.S.A. only)

This equipment generates,  uses, and can radiate radio frequency energy and if

not installed and  used  in accordance with the operating  instructions,  may cause
interference to radio communications.  It has been tested and found to comply

with the limits for a Class A computing device pursuant to Subpart J  of Part 15
of FCC  Rules, which  are designed to provide reasonable  protection  against

such  interference when operated  in a commercial environment.
Operation  of this equipment in  a residential area is  likely to cause interference in

which case the user at his own expense will be required to take whatever

measures may be required to correct the interference.

FEATURES

The TT-104B  is a  program timer having  4  independent output channels.

Weekly  program  capacity  is  30  steps  per  channel,  and  each  step  can  be  programed  in  an  increment  of  1

minute.

A channel assignment switch turns B, C and  D outputs into A output.

Programing,  its  change  or  cancellation  can  be  performed  easily  and  precisely  through  individual  key

operation  and  display.

Setting the pause mode allows no program output to be delivered.

Output is a no-voltage  make contact that connects for five seconds at the  programed time.

Built-in  buzzer audibly warns the user of key operation error.

Monthly error is  ±  5 seconds at 25 °C  of ambient temperature.

Clock and stored  programs can  be maintained for approximately 100 hours in the event of power outage.

INSTALLATION  PRECAUTION

Do not switch power on and off frequently because this can shorten the power-outage backup time.

Be sure to set the  memory backup switch to ON  after installation.

Do  not  install  unit  close  to  a  warm  air  vent  or  in  locations  where  the  unit  is  exposed  to  the  sunlight.

Installation  in  high  temperature  areas  like  on  the  amplifier  makes  a  clock  inaccurate.  Install  the  unit  in  the

area of which temperature is as close as possible to the room temperature.

Install the unit as far as possible from a radio tuner or a wireless microphone.

Be sure to ground the unit.

Be sure to unplug power cord from the wall outlet when making connections.

TOA Corporation

OPERATING  INSTRUCTIONS

TT-104B

Summary of Contents for TT-104



















Reviews: