background image

Form No. 3405-283 Rev A

Windshield Washer Fluid Kit

2015 and after Workman

®

GTX/HDX/MD/HD Series Utility Vehicle

Model No. 130-5615

Installation Instructions

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California to

cause cancer, birth defects, or reproductive harm.

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Description

Qty.

Use

No parts required

Prepare the machine.

Washer-fluid tank

1

Washer-fluid-tank bracket

1

Washer-fluid hose

1

Flange nut (5/16 inch)

4

Carriage bolt (5/16 x 3/4 inch)

4

Wire harness

1

Male straight fitting

1

Female straight fitting

1

Flange-head screw (1/4 x 5/8 inch)

2

Flange nut (1/4 inch)

2

Install the windshield washer fluid kit (GTX-series models).

Washer-fluid tank

1

Tank-support bracket (221 x 168 mm (8-11/16
x 6-5/8 inch) with 45° flange)

1

Carriage bolt (5/16 x 3/4 inch)

2

Flanged locknut (5/16 inch)

2

Carriage bolt (1/4 x 1-1/4 inch)

2

Strap

1

Spacer (1/4 inch)

2

Flanged locknut (1/4 inch)

2

Hose (3/16 inch)

1

Barbed hose connector

1

Wire harness

1

Push fastener

8

Install the windshield washer fluid kit (HD-series models).

© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3405-283* A

 

Summary of Contents for 130-5615





















Reviews: