background image

User Guide 
CPSMP-205 

110 – 240 VAC Power Supply Module:   

• PointSystem

 

• CPSMC1800-200 Accessory 
• CPSMC1900-100 Accessory

 

 

 

Contents 

Contents ........................................................................................................................................................ 1 
Description .................................................................................................................................................... 1 
Cautions and Warnings................................................................................................................................. 2 

Definitions ................................................................................................................................................. 2 
Power supply component identification .................................................................................................... 3 

Installation ..................................................................................................................................................... 4 

Configuration switch ................................................................................................................................. 4 
Configuring two power supplies in one chassis........................................................................................ 5 
Installing an optional power supply into the chassis................................................................................. 6 
Connecting power supply to external power............................................................................................. 8 

Maintenance.................................................................................................................................................. 9 

Replacing the CPSMP-205 power supply ................................................................................................ 9 
Replacing the fuse .................................................................................................................................. 11 

Technical Specifications.............................................................................................................................. 12 
Troubleshooting .......................................................................................................................................... 12 
Contact Us................................................................................................................................................... 13 
Compliance Information .............................................................................................................................. 13 

Declaration of Conformity ....................................................................................................................... 13 
Record of Revisions................................................................................................................................ 14 

 
 

Description 

Transition Networks’ CPSMP-205 AC power supply can deliver power or provide optional, redundant AC 
power to the CPSMC1800-200 and the CPSMC1900-100 PointSystem chassis.  
 
 

33458 Rev. B 

http://www.transition.com/ 

Page 1 of 14 

Summary of Contents for CPSMP-205















Reviews: