background image

®

SHREDMaster

OWNER'S MANUAL

v1

Congratulations on your selection of a Triminator ShredMaster. We want to help 

you to get the best results from your new shredder and to operate it safely. This 

manual contains the information on how to do that; please read it carefully before 

you set up and use your machine.  This manual is intended for all ShredMaster 

machines in different configurations.  If your equipment does not contain a 

component please disregard information relating to the omitted component.

Included in this manual are safety tips, operating instructions, preventative 

maintenance and lubrication schedules, trouble shooting information , and a parts 

list. For information or questions that may not be found in this manual please 

contact our service department at 

530-265-4277

THIS OWNER’S MANUAL IS CONSIDERED A PERMANENT PART OF 

THE MACHINE AND SHOULD REMAIN WITH THE SHREDDER IF RE-

SOLD. THE INFORMATION AND SPECIFICATIONS INCLUDED IN THIS 

PUBLICATION ARE THOSE THAT WERE IN EFFECT AT THE TIME OF 

APPROVAL FOR PRINTING. MOSMAN MACHINERY COMPANY, INC. 

RESERVES THE RIGHT, HOWEVER, TO DISCONTINUE OR CHANGE 

!

NOTICE

Summary of Contents for Shredmaster





















Reviews: