Hybrid DVR
Quick Start Guide
1
.
Notes
●
Please read this instruction carefully before operating the unit and
keep it for further reference.
●
All the examples and pictures used here are for reference only.
●
The contents of this manual are subject to change without notice.
●
This device should be operated only from the type of power source indicated
on the marking label. The voltage of the power must be verified before using
the same.
The interfaces of the rear panels are for reference only.
4. Rear Panel Instruction
5.
Startup
&
Shutdown
8.
Network Configuration & Add IP Camera
7.
Analog Camera Connection
You must configure the wizard if you start the DVR for the first time.
Please change the
password as needed and then click “Edit Security Question” to set questions
and answers for retrieving password.
The default
username is
admin
and the default password is
123456
.
►Startup
①
Connect the monitor and the power.
②
The device will boot and the power indicator will display blue.
③
A wizard window will pop up.
►Shutdown
Click “Start” and then select “Shutdown” icon. This will bring up a shutdown
window. The device will shut down by clicking “OK” button. Then disconnect
the power.
6.
Login
First connect the camera to the DVR. Then go to Start
→
Settings
→
Camera
→
Manage Camera
→
Camera Signal to set the signal mode of camera. The
actual signals input shall correspond to the video mode. Please refer to User
Manual for details.
④
Go to Start
→
Settings
→
Camera
→
Add Camera. The DVR will automatically
refresh the list of online IP cameras which are in the same local network with
the DVR. Click to modify the IP address.
Username
Password
Pattern Lock
Confirm Password
admin
Edit
Wizard
123456
123456
Display Password
Enable
Log In Automatically
Next
Edit ecurity
uestion
S
Q
Cancel
4.0.0.1.beta1
Version
80
No.
Address
Edit
Port
Protocol
Model
Subnet Mask
1
192.168.2.45
XXX
XXX
255
.
255
.
255
.
0
Quickly Add
Manually
Add
Add
Camera
Selected: 1/1
Add
Default Password
Remain
Bandwidth
:
10
/
10
Mb
Cancel
Mac Address
Address
Edit IP
192
.
168
.
1
. 45
255
.
255
.
255
. 0
admin
192
.
168
.
1
. 1
Subnet Mask
Username
Gateway
Password
OK
Cancel
CE :98 :23 :75 :35 :22
3
.
HDD
Installation
2
.
Packing Check
This series of the product supports 8 SATA hard drives. The pictures of the
installation are only for reference, please take the real object as the standard. Please
make sure that the device is powered off before the installation.
①
Remove
the
cover and loosen the screws to take out two mounting bars.
②
Fix the
HDDs on the mounting bar with screws.
Please check the device and accessories after getting the device. If there are
any damages, shortages or defects, please contact your dealer immediately.
③
Install the two mounting bars with HDDs back to the device ( It is recommended to
install the copper-pillar provided in case the HDDs are damaged by external forces ).
④
Connect the power and data cables.
⑤
Install back the cover and secure it with the screws.
Tips: Please check the inside structure of the device and make sure the cables connected
well before installing the cover back.
AUDIO IN
Connectors for audio input
VIDEO IN
AUDIO OUT
MIC IN
CVBS
LAN1/2
VGA
HDMI1
HDMI2
USB3.0/USB
RS 485
K/B: connector for a keyboard. A is TX+; B is TX-
P/Z: connector for a PTZ device. Y is TX+; Z is TX-
ALARM OUT
ALARM IN
E-SATA
RJ 45 1000Mbps Ethernet ports
Connectors for video input
Connectors for audio output
Connect to a microphone used for two-way talk
CVBS video output connector
Connect to monitor
Connect to monitor, used as main output
Connect to monitor, used as secondary output
Connect to USB storage device or USB mouse
Connector for alarm output devices
Connector for alarm input devices, like sensors
Connect to the HDD with e-SATA interface
►
LAN
①
Set the network of the DVR. Go to Start
→
Settings
→
Network
→
TCP/IP. Enter
IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the
NVR and the router.
②
Go to Start
→
Settings
→
Network
→
Port. Enter HTTP port (the default value
is 80), server port (the default port is 6036).
③
Click “Apply” to save the settings.
Network Fault Tolerance:
Bound
two
network
ports
to
one
IP
address. This pattern
can increase the network bandwidth and form a network redundant array to share the load.
When one port goes wrong, the other port will take over the entire load immediately and
seamlessly.
Multiple
Address
Setting:
You shall set the IP address, subnet mask, gateway and
DNS of each ethernet port respectively.
The pictures are only
for
reference
,
please
refer
to
User
Manual
for
details
.
IP Address Settings
Obtain an IPv4 address automatically
Obtain
DNS
automatically
Obtain an IPv6 address automatically
Ethernet Port 1 ( Online )
Ethernet Port 2 ( Online )
Address
MCA Address
Address
MAC Address
192 . 168 . 1 . 2
10 .
151 . 151 . 1
0 . 0 . 0 . 0
. . .
0
192 . 168 . 1 . 1
Network Fault Tolerance
Ethernet Port 1
1500
Subnet Mask
Preferred
DNS
Mask Length
Gateway
Primary Card
Work Pattern
(Modifying work pattern need to reboot )Gateway
Gateway
MTU
After you finish adding IP cameras, you can see the live images through the monitor
of the DVR. The following will mainly introduce how to add the IP cameras via
LAN/WAN. This DVR has two network ports, you can select the network work
pattern as needed. Network fault tolerance and multiple address setting are optional.
Admin Password Setup
