background image

1

FOSC 450 B6
Closure

I N S T A L L A T I O N   I N S T R U C T I O N

Fiber Optic Splice Closure

1.0 General Product Description

The FOSC 450 fiber optic splice closures use compressed-gel cable
seals to environmentally seal fiber cable splice points. 

The maximum single splice capacity of the FOSC 450 B6 closure is
144 with 24 splices stored on six trays.  The maximum mass fusion
splice capacity is 288, only four trays are needed.

A larger FOSC 450 D6 closure is also available.  Splice capacities for
the D size are 576 for single splicing and 1152 for mass splicing.

Note:  Cable blocking is not recommended in this closure due
to the space constraints.  If cable blocking is used, follow the
special instructions in "D/Gel Cable Block" installation instruc-
tions.

2.0 Kit Contents

•  Dome and clamp
•  Base and o-ring
•  Metal slack basket (optional)
•  Gel end-piece
•  Velcro strap
•  4 Gel end-piece plugs
•  2 or 6 Cable strain relief holders and cable clips
•  Hose clamps
•  6 Small and 2 large strength member attachment brackets 

with lugs

•  3 Bond clamps (3" long) -- optional
•  3 Braided grounding straps -- optional
•  12 Small tie wraps
•  1/4” Nut driver to install hose clamp
•  Installation Instructions

FOSC 450-ab-c-dd-e-fgh

a =    Closure size 
b =    Number of cable ports (6 for B-size)
c =    Number of cable ports for which termination hardware 
           is provided  (typically all ports or 2 ports)
dd = Capacity or type of splice tray (12, 24, NT [no trays])
e =    Number of trays pre-installed (1 or 0 [NT] is standard)
f =     Basket type (N=none or B)
g =    Number of ground feed-thru lugs (0 or 3)
h =    Valve for flash test (V = Yes [standard],  N = No)

Summary of Contents for FOSC 450 B6









Reviews: