background image

  

 

UPS-ST-600 

UPSPro

®

 

 

Outdoor UPS System

 

▫ 

Wireless Base Stations 

and Client Devices 

▫ 

Surveillance Cameras 

▫ 

Mission Critical Backup 

Power 

▫ 

Remote Sensors 

Congratulations! 

on your purchase of the UPSPro

®

Outdoor 

UPS backup power system. Please take a moment to review this 

Qwik Install Guide before assembly or battery installation. 

DANGER! Avoid Powerlines!  

You Can Be Killed! 

When following the instructions in this guide take extreme care 

to avoid contact with overhead power lines, lights and power circuits. 

Contact with power lines, lights or power circuits may be fatal. We rec-

ommend to install no closer than 20 feet to any power lines. 

Safety: 

For your own protection, follow these safety rules. 

▫ 

Perform as many functions as possible on the ground 

▫ 

Do not attempt to install on a rainy, windy or snowy day or if 

there is ice or snow accumulation at the install site or if the 

site is wet. 

▫ 

Make sure there are no people, pets, etc. below when you are 

working on a roof or ladder.

 

Recommended Tools: 

Phillips Screwdriver, Flat Blade Screw-

driver, 13mm and 10mm Wrench, 5/16” nut driver,

 

Please help preserve the environment and return 

used batteries to an authorized depot 

Summary of Contents for UPSPro UPS-ST-600









Reviews: