background image

PAGE 1 OF 9 

0415 IH-2665

π

  H-2665

SANITAIRE

®

BAGLESS VACUUM

1-800-295-5510

uline.com

SAFETY

NOTE: When using an electrical appliance, basic 
precautions should always be followed, including 
the following: READ ALL INSTRUCTIONS BEFORE 
USING THIS VACUUM CLEANER.

WARNING! To reduce the risk of fire, electric shock, 
or injury:

•  Do not use outdoors or on wet surfaces.
•  Do not leave vacuum cleaner unattended when 

plugged in. Turn off the switch and unplug the 

electrical cord when not in use and before servicing.

•  Do not allow to be used as a toy. Close attention is 

necessary when used by or near children.

•  Use only as described in this manual. Use only 

manufacturer’s recommended attachments.

•  Do not use with damaged cord or plug. If vacuum 

cleaner is not working as it should, has been dropped, 

damaged, left outdoors, or dropped into water, return 

it to a service center before using.

•  Do not pull or carry by cord, use cord as a handle, 

close a door on cord, or pull cord around sharp edges 

or corners. Do not run vacuum cleaner over cord. Keep 

cord away from heated surfaces.

•  Do not use extension cords or outlets with inadequate 

current carrying capacity.

•  Turn off all controls before unplugging.
•  Do not unplug by pulling on cord. To unplug, grasp the 

plug, not the cord.

•  Do not handle plug or vacuum cleaner with wet hands.
•  Do not put any object into openings. Do not use with 

any opening blocked; keep free of dust, lint, hair, and 

anything that may reduce airflow.

•  This vacuum cleaner creates suction and contains a 

revolving brush roll. Keep hair, loose clothing, fingers, and 

all parts of body away from openings and moving parts.

•  Do not place cleaner on furniture or stairs as the brush 

roll may cause damage. Place cleaner on floor with 

the handle in storage position while using attachments.

•  Do not pick up anything that is burning or smoking, 

such as cigarettes, matches, or hot ashes.

•  Do not use without dust cup or filter(s) in place.
•  Belt pulleys can become hot during normal use. To 

prevent burns, avoid touching the belt pulley when 

servicing the drive belt.

•  Use extra care when cleaning on stairs.
•  Do not use to pick up flammable or combustible 

liquids such as gasoline, or use in areas where they 

may be present.

•  Store your cleaner indoors in a cool, dry area.
•  Keep your work area well lit.
•  Unplug electrical appliances before vacuuming them.
•  This appliance is provided with double insulation. Use 

only identical replacement parts. See the following 

instructions for servicing of double-insulated appliances.

Summary of Contents for SANITAIRE H-2665










Reviews: