background image

U.S.SAWS CC - SERIES

OPERATING MANUAL

 

 

 

 

 

 

 

TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW WITHOUTPROPER TRAINING AND.  

UNDERSTANDING OF THE OWNERS MANUAL 

WHEN OPERATING THIS MACHINE 

 

 

ALWAYS WEAR SAFETY APPROVED 

 

 

 

HEARING PROTECTION 

EYE OR FACE PROTECTION 

PROTECTIVE HELMET

   

 

 

 

 

  

 

     

PROTECTIVE GLASSES OR FULL FACE PROTECTION 

 
 

      WEAR HAND PROTECTION 

WARNING: Improperly maintaining the JS  including the Honda  engine  or  failing  to  correct  a  problem  before 

operation could cause a malfunction resulting in a serious injury. Always perform a pre-operation inspection before 

each operation and correct any problem. See Honda Engines Owner's Manual. 

 

5.2

 

 

Check the condition of the Honda engine. See the section titled "Before operation - is your 

engine ready to go?" in the Honda Engines Owner's Manual. 

 

  

WARNING: Exhaust gas from gasoline engines contains dangerous carbon monoxide. Breathing it can cause 

unconsciousness and even kill you. Always operate gasoline engine machines in a well-ventilated area. Do not 

operate in areas where exhaust fumes could accumulate without wearing appropriate respiratory protection. 

Consult your employer and OSHA regarding use of appropriate respirator for dangerous carbon monoxide 

gases. See Figure 7. 

 

  

EEnnggiinnee  eexxhhaauusstt  ccoonnttaaiinnss  

ppooiissoonnoouuss  ccaarrbboonn  

m

moonnooxxiiddee  ggaass..  Breathing 

it could cause death.

 

Operate machine in well 

ventilated area.

 

 

 

 

FFiigguurree  77  --  W

Waarrnniinngg  llaabbeell  --  eennggiinnee  eexxhhaauusstt  ccoonnttaaiinnss  ccaarrbboonn  m

moonnooxxiiddee  ggaass  

1111  

U.S. English

02-11-2021

Notice of Copyright Protection

Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any 

means without the prior written permission of U.S.SAWS

Surface Prep

Division 

P: 877-817- 6687  F: 813-621-7125  

Visit us at www.ussaws.com 

sales@ussaws.com

Summary of Contents for CC - Series















Reviews: