background image

Button Functions

4

Programming the Remote Control

5

There are three ways you can program your 

CLIKR

TM

-5

remote:

* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method                                             * The Learning Method

The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers
that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and easiest of the three
methods. (Code Tables are on the backside of this Instruction Sheet.)  The Auto-Search Method scans through all
the codes in the remote control, one at a time.  The Learning Method allows you to transfer functions from other
remotes, one button at a time.

IMPORTANT SETUP NOTE!

This pertains to all programming steps. When you are in setup mode, a component  LED will light for 30 seconds.If
you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to
start over.  

A. Pre-Programmed 3-Digit Code Method

STEP1

Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote.

STEP2    

Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button
simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is
ready to be programmed.

STEP3    

Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.     

*Note : 

If the 3-digit code number you just entered is
correct, the Component will turn Off.  If it did not
turn Off, continue entering code numbers listed
for that brand until the Component turns Off.    

STEP4    

After you’ve entered the correct code number
and the Component has turned Off, press the
[POWER] button to turn the Component back
On.  Now it’s time to test the VOLUME and
MUTE buttons for the TV (or PLAY and STOP
buttons for VCR and DVD) to make sure they all
work.  If any of the functions do not work as they
should, repeat from STEP 3 using the next 3-digit
code number listed for that brand.    

STEP5    

Once you have found the correct 3-digit code,
save it by pressing the same [COMPONENT]
button one more time.  The Component LED
light will blink twice to confirm that the code
was successfully stored.  

Now, program the rest of your Components by
repeating STEPS 1-5

*Note :  

If the Pre-Programmed Method did not
work, or if the Code Tables do not list your
Component brand, use the Auto-Search
Method as explained in Section B.

B. Auto-Search Method

STEP1    

Turn on the Component you want to
program (TV, VCR, DVD or AUX) using your
old remote.

STEP2    

Press the [COMPONENT] button (TV, VCR,
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED light will turn
on for 30 seconds indicating the unit is ready
to be programmed.

STEP3    

Point the remote toward the Component and
press the [CH

]  or [CH

] button one step

at a time or keep it pressed.  The remote will
emit a series of ON/OFF commands.
Release the [CH

] or [CH

] button as soon

as the Component  turns Off. 

STEP4    

Test functions. (Same as for 3-Digit Code
Programming Method - Section A).  If any of
the functions do not work as they should,
repeat from STEP 3 using [CH

] or [CH

]

buttons to find the correct code.  

STEP5    

Save the code. (Same as for 3-Digit Code
Programming Method - Section A).

Now, repeat the Auto-Search Method for those
Components you could not program earlier with the
Pre-Programmed Method.  If you can’t find the right
code using the Auto-Search Method, try the Learning
Method in Section C.  

C. The Learning Method

STEP1    

Press the [COMPONENT] button (TV, VCR,
DVD or AUX) to be programmed and the [ # ]
buttons simultaneously for 3 seconds until
the Component LED light turns on. 

STEP2    

Line up the 

CLIKR

TM

-5

to the other remote,

head-to-head, 1 or 2 inches apart. 

STEP3    

Press any button on the 

CLIKR

TM

-5

that you

want to teach a command to.  For example,
if you want to teach the [MUTE] button,
press the [MUTE] button. 

STEP4    

Press and hold the [MUTE] button on the
other remote until the 

CLIKR

TM

-5

Component

LED light blinks twice.   

*Note  :

The LED will blink 5 times if there was an
error in the learning process.  In so, repeat
STEPS 3 and 4. Continue learning other
buttons by repeating STEPS 3 and 4. 

STEP5    

Once you have completed teaching

CLIKR

TM

-5

all desired commands for that

Component, save the learned commands by
pressing the [COMPONENT] and [ # ]
buttons simultaneously until the Component
LED blinks 3 times.  Now test all the buttons
to make sure they learned correctly.    

D. Erasing a Single Learned Command

STEP1    

Press the [COMPONENT] and [ # ]
buttons simultaneously for 3 seconds
until the Component LED light turns on.

STEP2    

Press and hold the button you want to erase
for 3 seconds.  The Component LED will blink
twice to confirm the erasure. 

STEP3    

To exit, press and hold both the
[COMPONENT] and [ # ] buttons
simultaneously until the Component LED
blinks 3 times.  

E. Erasing All Learned Commands from One Component

STEP1    

Press the [COMPONENT] and [ # ] buttons
simultaneously for 3 seconds until the
Component LED light turns on. 

STEP2    

Press and hold both the [COMPONENT]
button you want to erase and the [PAUSE]
button for 3 seconds.  The Component LED
will blink twice to confirm the erasure. 

STEP3    

To exit, press and hold both the
[COMPONENT] and [ # ] buttons
simultaneously until the Component LED
blinks 3 times.  

F. Finding a Component Button’s Setup Code Number

If you used either the Auto-Search or Learning
Methods to program a Component, you may not know
what the correct code number is.  Here is a way for
you to identify the code number, so you can record it
for future reference.

STEP1    

Press the [COMPONENT] button (TV, VCR, DVD
or AUX) you want to verify and the [OK/SEL]
button simultaneously for 3 seconds. The
Component LED light will turn on for 30 seconds.

STEP2    

Press the [INFO] button and count the number of
times the Component LED light blinks.  This
number indicates the first digit of the code,
followed by the second and third, each
separated by a one second pause when the LED
will turn off.  

Universal Remote Control, Inc.

www.universalremote.com

OCE-0045K  REV 03(04/14/07)

UR5L-8520L

Operating Instructions For

CLIKR

-5

Cable Remote Control

The 

CLIKR

TM

-5

UR5L-8520 is designed to

operate all Scientific-Atlanta, Pioneer
Voyager and Pace Micro digital set top
boxes (including DVR & HD), plus the
majority of TV, VCR, DVD and AUDIO
equipment on the market as shown below.

CABLE

: Cable Converters

TV

:  Televisions  

VCR

: VCRs and TV/VCRs   

DVD

: DVD Players

AUX

: Audio Receivers and DVRs, etc.

Introduction

1

DEFAULT STATE: 

Component Default:

CABLE

Channel Default:

CABLE channel and

numbers operate through the CABLE. You
have the option of controlling channel and
numbers through the TV, VCR or DVD. Refer
to section 

I

for programming steps.

Volume Default:

CABLE volume and mute

operate through the TV. You have the option
of controlling volume and mute through the
Cable box, VCR or DVD. Refer to section J 

J

for programming steps.

Operations

3

Replacing Batteries

2

Before you program or operate the remote
control, you must install two new AA alkaline
batteries.

STEP1    

Remove the battery compartment cover
on the back of your remote control.

STEP2    

Check battery polarity carefully, and
install the batteries as shown in the
illustration below.

STEP3   

Replace the battery compartment cover.

STEP2    

Press the [VOL 

] button.

STEP3    

Press the [TV] button again.  The Component
LED will blink twice to confirm the programming.

To return to original state:

If you wish to restore the CABLE channel control in TV

mode, repeat the above steps but press [CBL] in     

STEP3 .

J. Programming Volume Control

You can program the volume controls (Volume Up,
Volume Down and Mute) from one Component to
operate in another Component mode. Default volume
control settings on the remote control are as follows:

CBL

: TV 

T V

: TV

VCR

: TV 

DVD

: TV

AUX

: AUX

If you wish to store the CBL volume control in CBL mode,
use the following steps.

STEP1    

Press the [CBL] button and the [OK/SEL] button
simultaneously for 3 seconds.  The [CBL]
Component LED will turn on for 30 seconds.

STEP2    

Press the [VOL 

] button.

STEP3    

Press the [CBL] button.  The Component LED
will blink twice to confirm the programming.

To return to original state:

If you wish to restore the TV volume control in CBL mode,
repeat the above steps but press [TV] in    

STEP3

.  

K. Programming a ‘Macro’ or Favorite Channel

In CBL mode, the M1, M2 and HELP buttons can be
programmed to act as a ‘Macro’ or Favorite Channel
button. This allows you to send up to 10 commands with
one button press.

STEP1    

Press the [CBL] button to select the CBL mode.

STEP2    

Press the [M1,M2 or HELP] button and [OK/SEL]
button simultaneously for 3 seconds. The [CBL]
Component LED will turn on for 30 seconds.

STEP3    

Press up to 10 buttons you wish to store. The
[CBL] Component LED will blink once for each
command entered.

STEP4    

Press the [CH

] button to store the commands

that were selected. The [CBL] Component LED
will blink twice to confirm the storage of
commands.

L. Low Battery Warning

When the batteries are low and need to be replaced with
fresh batteries, the Component LED lights will blink 2
times in sequence whenever a [POWER] button is
pressed to turn on equipment.

M. Memory Lock System

This remote control is designed to retain programmed
memory for 10 years even after batteries are removed
from the remote control.

N. Record Your Component Set-up Codes

TV

Set-up Code Number:  

VCR

Set-up Code Number:

DVD

Set-up Code Number:

AUX

Set-up Code Number:

*Note  :

10 blinks represents the number zero.

Example :

One blink, (pause), eight blinks, ( pause) and
three blinks, indicates code number 183.

G. AUX Function: Programming a 5 

th

Component 

You can take advantage of the AUX function to program a 5

th

Component such as a second TV, VCR, DVD or Audio Component.

STEP1    

Turn on the 5

th

Component you want to program

(TV, VCR, DVD or Audio) using your old remote.

STEP2    

Press the [AUX] button and the [OK/SEL] button
simultaneously for 3 seconds.The [AUX]
Component LED will turn on for 30 seconds.  

STEP3    

Press the [COMPONENT] button you want to
setup.  Point the remote control toward the
Component and enter the 3-digit code number
assigned to your brand.  

*Note  :

If the 3-digit code number you just entered is the
correct number, the Component will turn Off.  If it
did not turn Off, continue entering code numbers
listed for that brand until the Component turns Off.  

STEP4    

Test functions.  (Same as for 3-Digit Code
Programming Method - Section A).  If any of
the functions do not work as they should, you
need to find a new code.    

STEP5    

Once you have found the correct 3-digit code,
save it by pressing the [AUX] button one more
time.  The Component LED light will blink twice
to confirm the code was stored.  Now when
you press the AUX button, all the buttons will
work with that 5

th

Component.  

H. Programming the System On/Off Button

This allows you to program the System On/Off button so it can
send up to five power On/Off commands with one button press.

STEP1    

Press the [CBL] button.

STEP2    

Press the [SYSTEM ON/OFF] button and the
[OK/SEL] button simultaneously for 3 seconds.
The [CBL] button will turn on for 30 seconds.

STEP3    

Press the first [COMPONENT] button you want
to store in the [SYSTEM ON/OFF] button and
then the [POWER] button.  Repeat this for other
Components until you have stored all the
desired power commands into the [SYSTEM
ON/OFF] button.

STEP4    

Press the [CH

] button to save the power

commands you stored. The [CBL] button will
blink twice to confirm the commands have
been saved.

I. Programming Channel Control

You can program the channel controls (Channel Up,
Channel Down and Last) from one Component to
operate in another Component mode. Default channel
control settings on the remote control are as follows:

CBL

: CBL 

T V

: CBL

VCR

: CBL 

DVD

: DVD

AUX

: AUX

If you wish to store the TV channel control in TV mode,
use the following steps.

STEP1    

Press the [TV] button and the [OK/SEL] button
simultaneously for 3 seconds.  The [TV]
Component LED will turn on for 30 seconds.

Reviews: