background image

 

 FLORIDA-PNEUMATIC.COM 

 

Please contact 1-800-356-3392 for further assistance.

Universal Tool

UT8788 

6-in.  DUAL ACTION SANDER

General Safety Information & Replacement Parts

WARNING:

 Risk of injury to persons. Read and 

understand operation instructions.  Always become familiar 
with all the instructions and warnings before operating any 
pneumatic tool.

TABLE OF CONTENTS

General Safety Information   . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 
Air Compressor and Air Tool Safety . . . . . . . . . . . . . . . . . . . 2-3 
Tool Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maintenance / Lubrication  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 

WARNING

:

 This product contains chemicals known to 

the State of California to cause cancer and birth defects or 
other reproductive harm. Wash hands after handling.

WARNING

:

 This product contains lead, a chemical known to 

the State of California to cause cancer and birth defects or 
other reproductive harm. Wash hands after handling.

Summary of Contents for UT8788









Reviews: