background image

GAS-FIRED INFRARED   

OUTDOOR PATIO HEATER   

Virco Associates, Inc.

              

INSTALLATION, OPERATION 

145, Brea Canyon Road           

MAINTENANCE INSTRUCTIONS 

Walnut, CA 91789, U.S.A. 

 

 

 
 
 
 
 
 

FOR MODEL PTH101 

 

TABLE OF CONTENTS

                                                  

PAGE 

IMPORTANCE ……………………………………………………………………   

  1 

TOOLS & PARTS ……………………………………………………………….. 

 

  2   

PRECAUTIONS………………………………………………………………….. 

 

  3       

ASSEMBLY INSTRUCTIONS …………………………………………………. 

 

  4     

GAS REQUIREMENTS & LEAK TESTING ………………………………….. 

 

  7   

SAFETY CHECKS ……………………………………………………………….   

  8   

LOCATING HEATER FOR USE ………………………………………………. 

 

  9 

LIGHTING / SHUTDOWN ……………………………………………………….       10   
STORAGE / BURNER REMOVAL………………………………..…………….   

  12 

BURNER INSTALLATION / PILOT CLEANING ………………………………       13 
BURNER REMOVAL …………………………………………………………….   

  14   

TROUBLE SHOOTING .…………………………………………………………   

  15 

PARTS LIST ………………………………………………………………………       16 
WARRANTY ………………………………………………………………………       18   

 

READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND BE SURE YOUR PATIO HEATER IS 
PROPERLY INSTALLED, ASSEMBLED AND CARED FOR. FAILURE TO FOLLOW THESE 
INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. IF 
YOUR HAVE QUESTIONS CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR 
DEALER, GAS APPLIANCE SERVICE REPRESENTATIVE OR YOUR GAS COMPANY. 

 

NOTE TO INSTALLER:   
LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION.   

 

NOTE TO THE CONSUMER:   
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.   

 

 

PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE.     

DO NOT RETURN TO PLACE OF PURCHASE. 

 

STOP 

Summary of Contents for PTH101






















Reviews: