ZL0059-0B
PAGE 1
©2008 Veris Industries USA 800.354.8556 or 503.598.4564 / support@veris.com
8251-0024C
05082
6%2)3).$5342)%3
Surge Protection
inStALLAtion guiDe
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
t 'PMMPXTBGFFMFDUSJDBMXPSLQSBDUJDFT
4FF/'1"&JOUIF64"PSBQQMJDBCMFMPDBMDPEFT
t 5IJTFRVJQNFOUNVTUPOMZCFJOTUBMMFEBOETFSWJDFECZRVBMJmFEFMFDUSJDBMQFSTPOOFM
t 3FBEVOEFSTUBOEBOEGPMMPXUIFJOTUSVDUJPOTCFGPSFJOTUBMMJOHUIJTQSPEVDU
t 5VSOPõBMMQPXFSTVQQMZJOHFRVJQNFOUCFGPSFXPSLJOHPOPSJOTJEFUIFFRVJQNFOU
t 6TFBQSPQFSMZSBUFEWPMUBHFTFOTJOHEFWJDFUPDPOmSNQPXFSJTPõ
t 3FQMBDFBMMEPPSTDPWFSTBOEQSPUFDUJWFEFWJDFTCFGPSFQPXFSJOHUIFFRVJQNFOU
Failure to follow these instructions will result in death or serious injury.
DANGER
XPSD1
XPSD1
/05*$&
t 5IJTQSPEVDUJTOPUJOUFOEFEGPSMJGFPSTBGFUZBQQMJDBUJPOT
t %POPUJOTUBMMUIJTQSPEVDUJOIB[BSEPVTPSDMBTTJmFEMPDBUJPOT
t 5IFJOTUBMMFSJTSFTQPOTJCMFGPSDPOGPSNBODFUPBMMBQQMJDBCMFDPEFT
t .PVOUUIJTQSPEVDUJOTJEFBTVJUBCMFmSFBOEFMFDUSJDBMFODMPTVSF
EQUIPMENT GROUNDING HAZARD
t %0/0564&0/6/(306/%&%4:45&.4
5IJTEFWJDFNVTUCFDPOOFDUFEUPUIFFRVJQNFOUHSPVOEUPGVODUJPO4VSHFWPMUBHFT
NVTUCFSFUVSOFEUPHSPVOEGPSEJTTJQBUJPO
Failure to follow these instructions will result in death or serious injury.
DANGER
POTENTIAL OF EQUIPMENT DAMAGE
t %0/0564&)*()70-5"(&5&45&26*1.&/5
5IFVTFPGB.FHHFS
®
PSPUIFSIJHIQPUFOUJBMUFTUHFBSXJMMEBNBHFUIJTTVSHF
QSPUFDUJWFEFWJDF5VSOPõBMMQPXFSBOEJTPMBUFUIFTVSHFEFWJDFCFGPSFUFTUJOH
Failure to follow these instructions can result in equipment damage.
CAUTION
quick install
Installer's Specifications
Max. Surge Current
45kA/phase
Housing
Type 1 (IP20)
Product Weight
0.56lb (255g)
Connection Method
Parallel
Terminal Capacity
#12-#4 AWG (3-25mm
2
)
Thermal Fusing
Yes
Operating Temperature
-30° to 70°C (-22° to 160°F)
Operating Frequency
50/60/400 Hz
Diagnostics
Green Status LED
Poles
4
Service Voltage
208Y/120V
Dry Contacts
Yes
Max. Surge Current per Phase
45kA
Rating
20A, Curve B
Supplementary Protection (Merlin-Gerin or Equivalent)
MG24149 or MG24164
Mount the XPSD1 to the DIN rail.
1.
Confirm the device is rated for your
2.
system by comparing the L-N voltage
measurements to the Service Voltage
(Un). See the specifications on the product
housing.
Insure that the MGSP or equivalent are properly rated and matched to the wire
3.
size.
Connect wires, keeping lead lengths as short as possible. Do not loop, bend, or coil
4.
wires.
CLICK
SPD
D1
D2
D4
D3
N
L3
L2
L1
N
G
L3
L2
L1
MSGP
Surge Protective Device
Keep lead lengths short. For best practice, ensure that D1, D2, D3, and D4 are each <20 inches.
