background image

PHASE EIGHT@

INSTRUCTIONS FOR
INSTALLATION 

AND OPERATION

CONTROLS FOR MOTORIZED

ZOOM LENSES

MODEL 

VlOOC, VlOOZF 

AND 

GENERAL

SCOPE

The information in this instruction manual
covers the installation, operation, and

maintenance of the following lens controls:

VlOOC
VlOOZF

These units should be installed using approved

materials and wiring practices in accordance
with the National Electrical Code and
applicable local wiring ordinances.

INTRODUCTION

This series of motorized zoom lens controls

enables remote operation of most Vicon zoom
lenses, including those with internal
electronic 

 circuitry. On each model,

circuit interlock prevents damage that could

occur when buttons for opposing functions are

pushed simultaneously. Speed control is
accomplished by a panel-mounted potentiometer

and internal range compensation.

These rugged controls are housed in the
compact PHASE EIGHT* module and contain
durable solid-state circuitry. PHASE EIGHT

modules may either be rack-mounted or
installed in desk-top units. The 

 Card

Cage is designed to fit in a standard 19-inch
rack. The 

 holds any combination of

single-, double-, or triple-size modules

totaling eight positions. When desk-top

REF. NOTES

SHEET NO. REV.

SEC.

SUPERSEDES

X104-386

X104 687

VlOOC LENS CONTROL

installations are desired, the 

 and 

are available with four and eight positions,

respectively. (See Associated Equipment and
Accessories for variation.)

Model VlOOC may be used with any Vicon
motorized zoom lens (indicated by the suffix M
in the part number) or with an Intraspot* lens
(suffix MS) when manual operation of the iris
is required.

Model VlOOZF is used both with motorized
zoom lenses (suffix AC or SND), which feature
internal 

 circuitry, 

and 

with cameras

not requiring iris control.

Model 

 is identical to Model VlOOC

except that it provides circuitry for control
of zoom lenses having a built-in motorized

extender (suffix MSX).

All models operate lenses up to the distances
shown in Table 1.

WARNING: TO PREVENT RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THESE UNITS TO RAIN OR MOISTURE.

Vicon part number 8006-9104-02-00

Product Specifications subject 

 change 

 

*Registered Trademarks of Vicon Industries Inc.

Patent pending on PHASE EIGHT.

 INDUSTRIES INC.

525 BROAD HOLLOW ROAD, MELVILLE. 

 11747 TEL: 

 293-2200 TELEX: 144581

TOLL FREE: 800-645-9116

(OUTSIDE OF NEW YORK)

Summary of Contents for V108C











Reviews: