background image

I N S T A L L A T I O N   S H E E T

BR250/651/752 Badge Reader

www.videofied.com

Doc. - Ref. 218-BR

Version : November 2016

The BR badge reader is designed to be used within a 
Videofied™  alarm system.
Its main features are :

•    Interactive wireless technology.
•    Dual tamper function.
•    Transmits check-in/status signals every 8 minutes
•    Lithium batteries : 4 years lifespan.
•   Mobility-Use outdoors or indoors with a fully 

weatherproof casing withstanding temperatures 
from -25°C to +70°C (-13°/158°F ).

Product presentation

Installation guidelines

RF testing will ensure good communication between the 
control panel and all system devices. Install the badge reader 
and other system devices in the order of the following steps :

>

  Program the badge reader and all other devices into the 

control panel and test RF communication from each intended 
device location to the control panel.

>

  Mount the badge reader at the final location.

Installation and Programming

The following provides summarized steps for device programming 
and testing.

Mount the base to the wall observing the “TOP” marking.

2

   Insert 3.6V DC LS14500 Lithium batteries observing correct 

polarity.

3

   With the programming keypad, browse to the ADD A NEW 

DEVICE menu (Level 4).

4

 

Press OK/YES. The keypad displays PRESS PROGRAM BUTTON 

OF DEVICE.

Press program button. The button blinks in green. Wait for 

keypad to display BADGE READER 

n

 RECORDED.

Press OK/YES. The display shows RADIO RANGE TEST?

Press OK/YES again to run the test. The keypad display shows 

TEST IN PROGRESS.

Please make sure the top LED blinks in red, indicating good 

communication with the control panel. The test result must stabilize at 
8/9 as a minimum. 

If the radio range level is below 8/9, change the location of the 
detector to obtain satisfactory radio range level.

9

 

Press OK/YES to end the radio range test then ESC NO.

10 

Choose a zone for that badge reader (by default that zone will be 

delayed ) and name it. 

11 

The keypad displays OPERATION COMPLETED ? Mount the 

badge reader on its base and press OK/YES. 

12 

Name the detector. When finished, keep ESC NO pressed to exit 

from configuration mode.

For full programming details, please refer to the control panel 
installation manual.

INIT

Button

Battery

Case

Summary of Contents for BR250

Page 1: ...g 1 Mount the base to the wall observing the TOP marking 2 Insert 3 6V DC LS14500 Lithium batteries observing correct polarity 3 With the programming keypad browse to the ADD A NEW DEVICE menu Level 4 4 Press OK YES The keypad displays PRESS PROGRAM BUTTON OF DEVICE 5 Press program button The button blinks in green Wait for keypad to display BADGE READER n RECORDED 6 Press OK YES The display shows...

Page 2: ...he incomplete arming detection in and instant area The LEDs will stay on for 5 seconds The two indicators turn off the system is disarmed There was no alarm An alarm triggered on The top indicator flashes green for 2s and that of the bottom flashes fixed green light and the reader beeps 4 times The two indicators remain on with fixed green light for 5 seconds When reading the badge the reader emit...

Page 3: ...ommunications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase ...

Page 4: ...amper Display lighting Automatic 2 LED Built in sounder Emits arm and disarm beeps Operating temperature 25 70 C 13 158 F Maximum relative humidity 95 non condensing Physical Data Protection rating IP44 IK08 Material Polycarbonate UL94 Dimensions 140 mm x 90 mm x 38 mm LxWxD 5 1 2 in x 3 1 2 in x 1 1 2 in Weight 136 g 4 8oz without batteries Installation Mounting Unit Base 2 screws secure the Badg...

Reviews: