background image

INSTITUTIONAL SPRINKLERS K5.6

TECHNICAL DATA

The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058

Telephone: 269-945-9501  Technical Services: 877-384-5464  Fax: 269-818-1680  Email: techsvcs@vikingcorp.com

Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com

Page 1 of 9

Form No. F_032319    20.01.03     Rev 20.1

© 2020 Viking Group Inc. All rights reserved

1.  DESCRIPTION

Viking Institutional Style Sprinklers are small, flush, solder link and lever sprinklers 

made with tamper-resistant construction. These flush-mount sprinklers can be 

ordered as Quick Response, Quick Response-Extended Coverage, and as Pendent 

or Horizontal Sidewall configurations. Viking institutional sprinklers have been 

specifically designed for use with concealed piping in institutional mental health 

occupancies, correctional facilities, or anywhere a likelihood of tampering with fire 

sprinklers by the occupants may exist.

The institutional sprinkler assembly consists of the sprinkler body and a 3 or 4 inch 

escutcheon plate. The sprinkler and escutcheon plate are available with a polished 

chrome or painted finish. 

2.  LISTINGS AND APPROVALS*

cULus Listed

: Category VNIV

Pendent: cULus Listed as Quick Response Flush sprinklers for standard areas of 

coverage in Light or Ordinary Hazard occupancies. 
EC Pendent: cULus Listed as Quick Response, Extended Coverage Flush sprinklers 

for extended areas of coverage up to 16’ x 16’ (4.9 m x 4.9 m) in Light Hazard 

occupancies only.
HSW: cULus Listed as Quick Response Flush sprinklers for standard areas of coverage 

in Light or Ordinary Hazard occupancies  below smooth, flat, horizontal ceilings only.
EC HSW: cULus Listed as Quick Response, Extended Coverage Flush sprinklers for 

extended areas of coverage up to 16’ x 16’ (4.9 m x 4.9 m) in Light Hazard occupancies 

only below smooth, flat, horizontal ceilings.

*  Refer to the Approval Chart and Design Criteria for requirements that must be followed.

 NOTICE

 

THE VIKING CORPORATION DISCLAIMS ANY RESPONSIBILITY FOR 

DAMAGES OR INJURY (INCLUDING DEATH) CAUSED BY THE OPERATION 

OR INOPERATION OF SPRINKLERS ARISING OUT OF THE MISUSE OF OR 

TAMPERING WITH VIKING BRAND SPRINKLERS INCLUDING, WITHOUT 

LIMITATION, ANY PERSONAL INJURY OR DEATH ARISING OUT OF OR 

CAUSED BY THE MANIPULATION OF, DISMANTLING OF, OR ATTEMPTED 

USE OF THE SPRINKLER OR ANY COMPONENT AS AN INSTRUMENT 

UNRELATED TO ITS INTENDED USE.  

3.  TECHNICAL DATA

Specifications:

Minimum Operating Pressure: 7 psi (0.5 bar)

Rated to: 175 psi (12 bar) water working pressure. 

Factory tested hydrostatically to 500 psi (34.5 bar).

Thread size: 1/2” NPT or 15 mm BSPT

Nominal K-factor: 5.6 U.S. (80.6 metric**)

** Metric K-factor measurement shown is in Bar. When pressure is measured in kPa, divide the 

metric K-factor shown by 10.0.

Material Standards:

Sprinkler Body: QM Brass or UNS-C84400 Casting

Deflector: Pendent - Copper UNS-C23000, HSW - Copper UNS-C51000

Deflector Pins: Stainless Steel 302

Button: UNS-C36000

Compression Screw: Brass UNS-C36000

Fusible Link Assembly: UNS-C51910 and Eutectic Solder

Fusible Link Levers: Stainless Steel UNS-S31600 

Lever Bar: Copper Alloy UNS-C72500  

Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with PTFE Tape

Seat: UNS-C31400 or UNS-C31600 Bronze 1/2 to full hard  

Pin Ring: Pendent - Copper UNS-C23000, HSW - Copper UNS-C51000

Ordering Information: (Refer to Table 1 and the current Viking List Price Book.)

SIN

THREAD DESCRIPTION

VK426 NPT

QR Pendent

VK650 NPT

QR EC Pendent

VK427 NPT

QR HSW

VK651 NPT

QR EC HSW

VK426 BSPT

QR Pendent

VK650 BSPT

QR EC Pendent

VK427 BSPT

QR HSW

VK651 BSPT

QR EC HSW

Replaces F_032319 Rev 19.2

(Replaced escutcheon PNs)

Summary of Contents for K5-6










Reviews: