background image

ASSEMBLY INSTRUCTIONS

WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A 
LICENSED ELECTRICIAN.

WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN 
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.

INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS 
ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL.

ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.

1. 

Position mounting plate (B) diagonally so that the holes of mounting plate (B) 

and wall outlet (A) are aligned. Tighten mounting plate (B) onto wall outlet (A) 

with screws (C).

2. 

Attach the ground (green) wire to the ground wire from the wall outlet box 

(usually green or copper in color), and fasten together with a plastic wire 

connector. Tightly wrap the wire connector with electrical tape so the end of the 

connector is sealed. IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR 

HOME BE PROPERLY GROUNDED.

3. 

Connect neutral (white) fixture wires to neutral (usually white) wire from wall 

outlet box (A). Fasten both wires together with a plastic wire connector and 

tightly wrap the wire connector with electrical tape.

4. 

Repeat the procedure with the hot (black) wires. Always make sure that no wire 

strands are left outside the connectors. DO NOT REVERSE THE HOT AND 

NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.

5. 

Gently push lantern box (F) onto outlet box (A), letting rods (D) pass through the 

holes on back plate of lantern box (F).

6. 

Position the light fixture and tighten by screwing washers/cap nuts (E) to the 

exposed part of rods (D) in clockwise direction. Remove lantern box cap (M) by 

unscrewing cap nut (0) & washer (N).

7. 

To install glass panel (L) provided to front section, make sure the metal tab (I) 

is flipped up. Place glass panel to the frame, secure the glass panel by bending 

back the metal tab (I) downwards. Repeat this procedure for the other two sides 

of lantern box (F).

Club Door Small Lantern

Item # CHO2401

CHO2401

ASSEMBLY & INSTALLATION GUIDE

WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.

WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT 
BREAKER BEFORE INSTALLATION.

INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL.  IF THERE IS ANY DAMAGE OR 
OBVIOUS DEFECT, DO NOT INSTALL.  

ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.

1. 

Position mounting plate (B) diagonally so that the holes of mounting plate (B) and wall outlet (A) are aligned. Tighten 

mounting plate (B) onto wall outlet (A) with screws (C).

2. 

Attach the ground (green) wire to the ground wire from the wall outlet box (usually green or copper in color), and 

fasten together with a plastic wire connector. Tightly wrap the wire connector with electrical tape so the end of the 

connector is sealed. IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE PROPERLY GROUNDED.

3. 

Connect neutral (white) fixture wires to neutral (usually white) wire from wall outlet box (A). Fasten both wires 

together with a plastic wire connector and tightly wrap the wire connector with electrical tape.

4. 

Repeat the procedure with the hot (black) wires. Always make sure that no wire strands are left outside 

the connectors. DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE 

COMPROMISED.

5. 

Gently push lantern box (F) onto outlet box (A), letting rods (D) pass through the holes on back plate of lantern box 

(F).

6. 

Position the light fixture and tighten by screwing washers/cap nuts (E) to the exposed part of rods (D) in clockwise 

direction. Remove lantern box cap (M) by unscrewing cap nut (0) & washer (N).

7. 

To install glass panel (L) provided to front section, make sure the metal tab (I) is flipped up. Place glass panel to the 

frame, secure the glass panel by bending back the metal tab (I) downwards. Repeat this procedure for the other two 

sides of lantern box (F).

8. 

Attach light reflector (J) to hook (K). Note: Insert from the top opening of lantern box (F).

9. 

Replace lantern box cap (M) on top of lantern box (F) and secure with cap nut (0) & washer (N).

10.  Insert light bulbs (not included) into sockets. Close front door (H) and secure with key (G).

11.  INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/OR IN WET LOCATION: 

A. Mounting surface should be clean, dry, flat and 1/4” larger than canopy/fixture base on all sides. Any gaps 

between the mounting surface and canopy exceeding 3/16” should be corrected as required. 

B. With silicone (ex. GE-l08) caulking compound, caulk completely (M around where back of canopy meets the wall 

surface to prevent water from seeping into outlet box.

WET

Reviews: