background image



911352-00

© Allegion 2014

Printed in U.S.A.

911352-00 Rev. 01/14-d

Customer Service

1-877-671-7011

www.allegion.com

Installation Instructions - Electrical

CX33A/35A 

CX98/99

Chexit Device

PUSH UNTIL ALARM SOUNDS

DOOR CAN BE OPENED

IN 15 SECONDS

CX Exit Device

(CX98/99 Rim shown)

Chexit Module

 Cable

Door Sign

Do not exceed rated

specifications.

WARNING

!

The Chexit device must be

installed in accordance

with these instructions by

a qualified electrician.

WARNING

!

Wiring must be in

accordance with all local

codes and regulations.

WARNING

!

GENERAL INFORMATION

ELECTRICAL SPECIFICATIONS

Voltage .................................................... 24 VDC
Current (Chexit) ....................................... 0.4 A
Current (Electric mortise) ......................... 0.3 A
Current on arming ................................... 300-mS 16-A in-rush
External alarm dry contacts (NO and C) ... 24 VDC, 1 A rating
Normally closed inputs ............................ Fire alarm (FA; 

required

)

External inhibit (EI)
Door position switch (DPS)

 

 

The Von Duprin Chexit device is designed for accident hazard or fire exit applications. It meets both life 
safety and security needs as well as all requirements of NFPA101

®

 for “Special Locking Arrangement” and 

UBC “Special Egress-Control Devices.” 

The Von Duprin Chexit device sounds an alarm and keeps an exit door secured for 15 seconds following 
an attempt to exit. The Chexit releases immediately upon a fire alarm condition.                                                   

Summary of Contents for CX33A









Reviews: