background image

*941369-00*

941369-00

Motorized Locking Trim

M996L Series

Installation Instructions

M996L

for Rim/Vertical

M996L

for Mortise

Parts Included

Tools Needed    

⁵⁄₁₆

" Nut driver

#2 Phillips

1

Retrofit / replace operation if necessary. 

(See M996L Series Retrofit, 941389-00)

Change function (Fail Safe or Fail Secure) if necessary.

2

Fig. 2-1

Unit locks when electric 

power is applied and 

unlocks when power is 

removed

FS (fail safe)

factory setting

Unit unlocks when 

electric power is applied 

and locks when power 

is removed

FSE (fail secure)

2.1.

  To change function, use the tip of a small screwdriver to CAREFULLY move the switch to the desired position. The  

 

switch is factory set to fail safe (FS). Moving the switch changes the function to fail secure (FSE). After changing FS/FSE  

 

switch position, power cycle the unit two or more times before installation. See Figure 2-1. 

FS

FSE

FS

FSE

CAUTION

!

Product is shipped in Fail Safe (FS) configuration. Fail Safe configuration is required by code in some applications (typically fire 

stairwells). Consult building codes before converting to Fail Secure (FSE) configuration. See page 8 for FS/FSE function information.

M996 Motorized Module

Summary of Contents for M996L Series









Reviews: