background image

 
EN-XXX_ECOplus-Solar-Storage_MA-201026-1WA10603 

1

Wagner Solar

INSTALLATION INSTRUCTIONS

ECOplus Solar Storage

Figure 1  ECOplus solar storage

Content

1  General Safety Notes                                                      2
1 1  Standards and Codes                                                                             2
1 2  Qualifications of the Installer                                       2
1 3  Intended Use and Application                                      2
2  Scope of supply                                                              2
3 Installation                                                                      2
3 1 Preparation                                                                      2
3 2  Setting up the Storage                                                  2
3 3  Connecting the Domestic Water Circuit                             4
3 4  Connecting the Solar- and Auxiliary Heating Circuit           5
3 5  Connecting Backup Heater                                          5
3 6  Installing Temperature Sensors                                   5

3 7  Install a Impressed Current Anode                              6
4  Startup of the System                                                                             6
4 1  Acceptance Protocol                                                      6
4 2  System Check                                                                  6
4 3  Flushing the Installation                                                                       6
4 4  Settings at Boiler and Solar Controllers                      6
4 5  Filling, Venting, Pressure Check                                   6
5  Place the Insulation                                                                                   7
6 Troubleshooting 

                                                            8

7 Maintenance                                                                  8
8  Disassembly and Recycling                                          8

Summary of Contents for ECOplus









Reviews: