FITTING & USAGE INSTRUCTIONS
• Remove from the carton and discard all packaging material.
• Place on a level (horizontal) surface.
• Open the lid and side windshields and lock them into place.
• Lift the trivet, remove the hose and connect it to the inlet connection. Tighten firmly
by hand.
• Make sure the valves are turned off on both the appliance and gas cylinder prior to
connecting or removing the stove.
• Firmly fasten the hose to the gas cylinder control valve.
• Ensure the controls on the stove are in the OFF position. Turn the gas cylinder control
valve on. Check for leaks at all gas joints by applying a soapy water solution.
• If a leak is detected by observing a stream of bubbles or by the distinct gas odour, turn
off the cylinder valve and do not use the appliance until the source of the leak has been
successfully fixed. Re-test for leaks each time before igniting the appliance.
• Turn each burner control on individually and light the gas at the burner using a match
or by repeatedly pushing the peizo push button (if fitted) for 5 seconds or until lit. If the
burner fails to light turn off the gas supply and wait for 5 minutes before reattempting
to ignite the burner.
• Use the stove control knobs to obtain the desired heat setting by turning anti-clockwise
to increase the heat and clockwise to decrease the heat.
• When alight, the gas stove should never be left unsupervised.
• Do not move this appliance during operation.
• After use, turn the gas cylinder valve off, wait for the flame to go out, then turn the
appliance control valve(s) off.
• During use, parts of the stove can reach high temperatures. After use, allow stove to cool
before handling.
• The burner extinguishing during use may indicate that the gas cylinder has run out of
gas. If this occurs replace the empty gas cylinder with a full gas cylinder and attempt
to reignite the burners. If the burners do not ignite there may be a blockage in the
injectors or the flexible hose. Replace the components as required to make the appliance
serviceable or take the appliance to a service centre to be professionally repaired.
• To ensure maximum life from your appliance it should always be stored in a dry place, out
of direct sunlight.
• To check if gas cylinder contains gas, disconnect from the cooker, then hold upright and
shake from side to side. If you can feel or hear liquid movement from within the cylinder,
it contains gas.
• Before each use, check primary air openings and clear blockages.
• Abnormal operation which may require service can be identified by black sooting of
cooking utensils, or an irregular burner flame which is yellow or unstable.
REPLACING JET (INJECTOR)
• Should there be a problem with the stove such as difficulty in lighting the burner or
sustaining a clear blue flame, the jet may require cleaning or replacing.
• Unscrew the burner from the stove base and remove trivet.
• Using a spanner, unscrew the jet (clockwise from front of stove).
• Blow out the blockage, or wash the jet in white spirits. Do not use needles or pins to
clean the jet. Damage could result making the gas stove dangerous.
• Firmly screw the jet back in place.
• Screw on the burner, replace trivet.
• If the blockage cannot be removed, replace the injector.
• Jet Service pack AN1920J.
REPLACING ‘O’ RINGS
• Gas leaking from the front of the control indicates that the “O” Rings MUST be replaced
before igniting the appliance.
• Turn off all controls on the appliance as well as the cylinder.
• Disconnect the flexible hose from the appliance and the cylinder.
• Remove the control knob by pulling forward away from the stove.
• Remove the control locking nut located directly behind the control knob by rotating in an
anti-clockwise direction.
• Remove the control spindle by rotating in an anti-clockwise direction.
• Remove the damaged “O” Rings from the spindle and replace with new ones.
• Reassemble in the opposite order of disassembly. Note: Push in spindle before turning
clockwise.
• “O” Ring (Spindle) Service Pack AN1992.
MAINTENANCE
This appliance does not require regular maintenance, however each time before use it should
be verified that it is in a suitable working condition. If any faults are detected the appliance is
not to be used until they have been rectified.
SPECIFICATIONS
Consumption Rate: 230 g/h (11mJ/h) per burner
For use with LPG
Injector size: Australia 0.20mm
This appliance shall only be used with a propane gas cylinder certified to Australian Standard
AS2030. IT MAY BE HAZARDOUS TO ATTEMPT TO FIT OTHER TYPES OF GAS CONTAINERS.
Operating Pressure: Vapour Pressure.
Turn anti-clockwise
to turn on and
increase flame
Turn clockwise to
decrease flame and
turn off
PARTS LIST
WA1025-04 Drip Tray and WA1025-10 Ignition included under trivet for model WA1025D.
*WA1025-07 foldaway legs for model WA1025 only.
WA1025-01 Knob
WA1025-02 Spindle
WA1025-03
Control “O” rings
WA1025-04
Drip Tray (Model WA1025D only)
WA1025-05 Trivet
WA1025-06
Jet (Injector)
WA1025-07
Foldaway leg (Model WA1025 only)
WA1025-08 Burner
WA1025-09 Windshield
WA1025-10
Piezo Ignition (Model WA1025D only)
WA4742
Hose (included)
Control Assembly
WA1025-01
WA1025-09
WA1025-08
WA1025-03
WA1025-02
*WA1025-07
WA1025-06
WA1025-05
WA4742
WA1025-010
CONTROL
KNOB
