background image

 

 

 

 

S200-P Series Centrifugal Fire Pumps 

    

Operation and Maintenance Instructions 

 

 

Table of Contents

 

Safety Information ................................................................................ 2, 3

 

Introduction

 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4

 

General Description

 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4

 

Operational Limits .................................................................................... 4

 

Components ............................................................................................. 5

 

Operating Instructions

 

Pumping from Hydrant or in Relay ......................................................... 6 

Pumping from Water Tank  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7 

Pumping from Draft  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8 

 
 
 
 

 

Read through the safety information 
and  operating  instructions  carefully 
before using your S200-P Series Fire 
Pump.

 

Fire Hose Testing ................................................................................... 9 

Maintenance ........................................................................................... 10

 

Mechanical Seal ................................................................................... 10 

Lubrication ........................................................................................... 10 

Testing .................................................................................................... 10

 

NOTE: Instructions subject to change without notice 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

F-1031, Section 2124-P (Rev. 3/23/17) 

 

 

 

Waterous Company, 125 Hardman Avenue South, South St. Paul, MN  55075  USA   651-450-5000 

www.waterousco.com

 

Summary of Contents for S200-P Series











Reviews: