background image

Applies to Product Revisions A – D

© March 2019

ORDERING INFORMATION

PART NO

DESCRIPTION

QCL500 OEM

500 mA Low Noise QCL Driver

QCL1000 OEM

1.0 A Low Noise QCL Driver

QCL1500 OEM

1.5 A Low Noise QCL Driver

QCL2000 OEM

2.0 A Low Noise QCL Driver

QCL OEM(+) Series

Positive polarity OEM models

PWRPAK-24V

24 VDC switching power supply 

(2x required)

WCB312

Dual power supply wiring kit

NOISESCAN

Noise characterization scan

55-110014

SMA-BNC low noise cable

WCB310

SMA-SMA low noise cable

QCLTL Series

Test load kits for the QCL OEM

LOWEST-NOISE DRIVER AVAILABLE

The QCL OEM Series drivers use patented

1

 circuitry to 

produce the lowest current noise density of any commercially 

available QCL driver. The 500 mA QCL driver exhibits noise 

performance of 0.4 μA RMS to 100 kHz, and average current 

noise density of 1 nA / √Hz—the lowest available.

ULTRA-NARROW QCL LINEWIDTH

In order to maintain their characteristically tight center 

linewidths and minimize jitter, quantum cascade lasers must  

be powered by drivers with exceptionally low current noise 

density. Our customers have reported achieving narrower 

linewidths with these drivers than any other they’ve used.

1.  Covered  by  U.S.  Patents  6,696,887;  6,867,644  and  7,176,755.  Licensed  from 

Battelle Memorial Institute.

APPLICATIONS

The QCL Series drivers are used in trace element detection 

systems,  both  laboratory-based  and  field-deployed. 

This driver is well suited  to applications requiring fast 

measurement times and ultra high sensitivity. 

REVERSE POLARITY AVAILABLE

Often, with epi-down configurations of a QCL, the exit 

lead is attached to the case and it is desirable to ground 

it.  Now, the reverse polarity driver, a current source, is 

also available in the OEM package.  See QCL OEM(+).

PROTECT YOUR QCL INVESTMENT

All the essential control and monitor functions you expect in 

a Wavelength laser driver are incorporated into this driver, 

along with protection circuitry to safeguard your QCL from 

minor  power  source  faults,  over-temperature  conditions, 

and electrical faults.

FEATURES AND BENEFITS

• 

Off-the-shelf models at 500 mA, 1 A, 1.5 A, 2 A

•  Can be delivered in other current ranges up to 2 A

• 

Compliance voltage 16 V (standard), 

 

Compliance 7-20 V with factory modification

•  Safety features protect your QCL investment

 

»

Adjustable soft-clamping current limit

 

»

Brown-out, reverse-voltage, & over-voltage 

protection

 

»

Driver over-temperature protection circuit

 

»

Relay shorts output when current is disabled

•  Local and Remote Power-On and Enable control

•  Analog modulation input between -5V and +5V

CONTENTS

QUICK CONNECT GUIDE

 

2

PIN DESCRIPTIONS

 

3

ELECTRICAL SPECIFICATIONS

 

5

SAFETY INFORMATION

 

7

OPERATING INSTRUCTIONS

 

8

TROUBLESHOOTING

 

13

TECHNICAL SUPPORT INFORMATION

 

14

MECHANICAL SPECIFICATIONS

 

22

CERTIFICATION AND WARRANTY

 

23

PAGE

www.teamWavelength.com

QCL OEM Series

Low-Noise Quantum Cascade Laser Driver

DATASHEET AND OPERATING GUIDE

Distributor

info@amstechnologies.com
www.amstechnologies-webshop.com

Summary of Contents for QCL OEM Series
























Reviews: