background image

Vieluxe

®

27" Built-In Grill

(Model #: 360251)

Vieluxe

®

39" Built-In Grill

(Model #: 370251)

Any Surface

Any Surface

26 inches Any Surface

26 inches

26 inches

Grill Frame

24 inches min. for lid clearance

WARNING: The structure, “island”, countertops, and adjacent work areas for the built-in 

grill installation must be built from non-combustable materials only.

NOTE: If you have questions on what materials are considered non-combustable, contact you
local building materials supplier or fire department.

LOCATING YOUR  GRILL

When determining a suitable location for your Vieluxe

®

gas grill installation, give attention to concerns such as exposure to wind,

proximity to traffic paths, and keeping any gas supply lines as short as possible. Never locate the Vieluxe

®

gas grill in a garage,

breezeway, shed, under an unprotected overhang, or other enclosed area. Locate the grill and structure so there is enough room to
safely evacuate the area in case of a fire.

THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONLY.

61265 021304

Built-In Liquid Propane Gas Grill Installation Guide

CLEARANCE FROM SURFACES OR STRUCTURES

WARNING: Clearance from any surface or structure is 26 inches from the back and sides 

of the grill. Refer to “Typical Gas Supply Installation” before starting installation.

Summary of Contents for Vieluxe 27 Built-In Grill














Reviews: