background image

WE EL-11

Trademark

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

E

N

G

LIS

H

SI

A

Ç

N

A

RF

L

O

Ñ

AP

S

E

WEED EATER

7349 Statesville Road

Charlotte, NC 28269

WEED EATER

850 Matheson Blvd. West

Mississauga, Ontario L5V 0B4

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Read instructions carefully before assembling.

Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual del operador y siga todas las advertencias e instruc-

ciones de seguridad. Antes de ensamblar el producto lea cuidado-

samente el instructivo. El no hacerlo puede resultar en lesiones gra-

ves.

AVERTISSEMENT:

Veuillez lire le manuel de l’utilisateur et bien respecter tous les

avertissements et toutes les instructions de sécurité. Bien lire les

instructions avant d’assembler l’outil. Tout défaut de le faire pourrait

entraîner des blessures graves.

115253326

245157

®

 

Rev.3  05/07/10  JBW

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner l’outil au détaillant.

Register your product online at:

Registre su producto en línea en:

Enregistrez votre produit en ligne à l’adresse :

1-800-554-6723

www.weedeater.com

Summary of Contents for 115253326










Reviews: