background image

ENGLISH

A

C

D

B

N (2x)

K

J

Ensure tight cable 

connection.

Lay excess cable flat inside the 

bottom of the interior housing.

Install interior assembly

align

A

B

C

G

M

R

K

P (3x)

If needed, re-key the 
lock to work with your 
existing key. See the 
supplied SmartKey 
Re-key instructions for 
more information.

ball tip

Keep “R” in a safe place, as you will 
need it to access the back panel for 
additional programming.

Install the battery cover and re-key the lock

Programming 
instructions are 
located on the 
reverse side of 
this document.

Program the lock

B2 / B3

 (2x)

B1 (2x)

B

Longer screws install 

closest to door jamb.

Install strike

A

A2

Determine required latch and extend latch bolt

For doors with chiseled edge

For doors without chiseled edge 

Use and programming 
instructions are located on the 
reverse side of this document.

A

A2

B

C

D

E

F

H

J

L

M

K

N

Q

R

P

G

B1

B2

B3

Parts in the Box

Latches and Strikes

Exterior Assembly

Interior Assembly

9

Required Tools

Additional Tools (depending on application)

1"

25 mm

2-1/8"

54 mm

1-1/2"

38 mm

1-3/8" — 1-3/4"

35 mm — 44 mm

Check dimensions

Additional door preparation may be 

required for doors with 1-1/2" 

(38 mm) holes. Consult the drilling 

instructions at www.weiserlock.com.

2-3/8" (60 mm)

or

2-3/4" (70 mm)

or

180°

A

B

A / A2

Hold the latch in front of the 

door hole, with the latch face 

flush against the door edge.

If the latch holes are 

centered in the door hole, no 

adjustment is required. 

Proceed to step 4.
If the latch holes are NOT 

centered, adjust latch. See 

“Latch Adjustment.”

Latch Adjustment (only if needed)

Adjust the backset of latch (if needed)

A

A2

C (2x)

A

B

C

D

Install latch

For doors with chiseled edge 

For doors without chiseled edge 

wood 
block

2-1/8"
54 mm

1-1/2"
38 mm

F

F

E

F

E

Prepare exterior keypad

For doors with 2-1/8" (54 mm) holes

For doors with 1-1/2" (38 mm) holes

Make sure “F” is 
installed on “E”

Remove and 
discard “F”

A

B

C

D

Q (2x)

E

J

H

Q

Keep parallel to 

edge of door

Tighten 
screws 
evenly

Insert key and test latch. If 
latch does not extend or 
retract smoothly, adjust 
screws (Q). 
Remove key when finished 
and make sure the latch 
bolt is fully extended.

Install keypad and mounting plate

Cable goes 
underneath 
latch

Route cable 
through center 
hole, then push 
cable into 
bottom hole. 

A

B

C

D

E

M

M

K

K

L

K

AA

L

4x

Disassemble interior assembly and load battery pack

Make sure 

turnpiece is in the 

vertical position.

Make sure 

turnpiece shaft is 
rotated as shown.

Ensure correct polarity. For best 
results, use new non-rechargeable 
Alkaline batteries only.

Do not install 

battery pack yet!

1-3/4

" (44 mm)

1-3/8

" (35 mm)

2-3/8" (60 mm)

2-3/4" (70 mm)

Edge

Backset

Face

Centerline

If your door requires drilling, cut out the template and place it on the exterior side of the door.  
Complete door drilling instructions are available on the SmartCode deadbolt page of www.weiserlock.com.

Template

Fold

Installation Guide

A

B

L

L

Press and hold

 the 

Lock button while 
installing battery 
pack (L).

Hold button until the 
latch bolt starts 
moving on its own.

This step will teach your lock the orientation of your door 

and is crucial to lock operation.

HOLD

latch bolt

Did the latch bolt retract 

and extend on its own 

when the battery pack 

was installed?

Door handing process 

was successful! 

Proceed to Step 11 

after latch bolt stops 

moving.

Remove battery pack, 

wait 15 seconds, then 

attempt the process 

again.

YES

NO

Perform door handing process

10

11

12

13

A

B

C

12"

305 mm

L

L

Perform the Inclusion process (Z-Wave locks only)

Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave 

controller, and initiate the Inclusion process at the controller. Refer to your 

Z-Wave control system instructions for more information. 

Press button “A” on the lock one time to include it in your system. The 

controller and lock must remain stationary for a total of 60 seconds during 

the Inclusion process.

If Inclusion is unsuccessful, initiate the Exclusion process at the controller, 

then press button “A” on the lock one time. Once the lock is fully excluded 

from the system, repeat the Inclusion process.

“Inclusion” refers to the process in which the lock is added to a Z-Wave or ZigBee controller.  

ZigBee locks: Perform the Inclusion process after installation is complete. 

See “Z-Wave and ZigBee Systems” on the reverse side of this document.

 Button 

“A”

Z-Wave

Controller

3

4

5

6

7

8

1

2

61041 / 02
GED1800

Reviews: