background image

GB1

IMPORTANT SAFETY INSTRUCTIONS 

YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT

This manual and the appliance itself provide important safety warnings, to be read and observed at all times.

This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others.

All safety warnings are preceded by the attention symbol and the following terms:

indicates a hazardous situation which, if not avoided, will cause serious injury.

indicates a hazardous situation which, if not avoided, could cause serious injury.

All safety warnings give specific details of the potential danger/warning present and indicate how to reduce risk of injury, damage and electric shock resulting
from improper use of the appliance. Carefully observe the following instructions:

Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturer's instructions and local safety regulations.
Do not repair or replace any part of the appliance unless specifically stated in the user manual.

The appliance must be disconnected from the power supply before carrying out any installation work.

Regulations require that the appliance is earthed.

The power cable must be long enough for connecting the appliance, once fitted in its housing, to the power supply socket.

Do not pull the power supply cable in order to unplug the appliance.

The electrical components must not be accessible to the user after installation.

Do not touch the appliance with any wet part of the body and do not operate it when barefoot.

The appliance is not intended for use by persons (including children) with any physical, sensory or mental impairment, or without experience and
knowledge of the appliance, unless supervised or previously instructed in its use by those responsible for their safety.

Customer care: do not repair or replace any parts of the appliance, unless specifically recommended by the manual. All other maintenance operations must
be carried out by a qualified technician.

When drilling through the wall pay attention not to damage electric connections and/or pipes:

Air vents must always discharge to the outside.

The manufacturer rejects all responsibilities for any damage caused by improper use or wrong settings.

Appropriate maintenance and cleaning ensure the good working order and the best performance of the appliance. Regularly clean all stubborn surface dirt
to avoid grease build up. Remove and clean or change the filter regularly.

Never flame cook food (flambé) under the appliance. Using free flames might cause fire.

The discharge air must not be discharged in ducts that are being used to discharge combustion fumes from gas heaters or heaters using any other
combustible materials. The appliance must have its own dedicated discharge outlet. All national requirements of art. 7.12.1 of CEI EN 60335-2-31 must be
strictly complied with.

If the hood is being used at the same time as other appliances using gas or other combustible materials, the negative pressure of the room must not exceed
4 Pa (4x 10-5 bars). For this reason ensure that the room is well ventilated.

Do not leave frying pans unattended when frying, as the frying oil may catch fire.

Before touching the light bulbs, ensure that they are cold.

Do not use or leave the hood without the light bulb correctly fitted, as this may cause electric shock.

The hood is not a worktop, therefore do not place any objects on top of it or overload it.

During all installation and maintenance operations wear appropriate working gloves.

This appliance is not suitable for outdoor use.

Scrapping of household appliances

This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. Before scrapping, cut
off the power supply cable.

For further information on the treatment, recovery and recycling of household electrical appliances, contact your competent local authority, the collection
service for household waste or the store where you purchased the appliance.

KEEP THIS BOOKLET FOR FUTURE CONSULTATION.

WARNING:

DANGER

:

Summary of Contents for 891











Reviews: