background image

INSTALLATION INSTRUCTIONS

30" (76.2 CM) FREESTANDING GAS RANGES

RANGE SAFETY

Table of Contents

RANGE SAFETY............................................................................. 1

INSTALLATION REQUIREMENTS ............................................... 3

Tools and Parts............................................................................ 3
Location Requirements ............................................................... 3
Electrical Requirements............................................................... 5
Gas Supply Requirements .......................................................... 5

INSTALLATION INSTRUCTIONS ................................................. 7

Unpack Range............................................................................. 7
Install Anti-Tip Bracket ................................................................ 7
Make Gas Connection................................................................. 8
Verify Anti-Tip Bracket Is Installed and Engaged ....................... 9
Level Range ............................................................................... 10
Electronic Ignition System......................................................... 10
Warming Drawer or Premium Storage Drawer ......................... 12
Storage Drawer.......................................................................... 12
Oven Door.................................................................................. 13
Complete Installation................................................................. 13

GAS CONVERSIONS ................................................................... 14

LP Gas Conversion.................................................................... 14
Natural Gas Conversion ............................................................ 17

W10658550A

IMPORTANT:

 

Save for local inspector's use.
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.

You can be killed or seriously injured if you don't immediately 
 

You

 

can be killed or seriously injured if you don't follow 

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety 
messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Summary of Contents for W10658550A





















Reviews: