background image

W10904260B

W10904262B-SP

Table of Contents

DRYER SAFETY .......................................................................... 2

INSTALLATION REQUIREMENTS

 .........................................

4

 

Tools and Parts .................................................................... 4

LOCATION REQUIREMENTS ..................................................... 5

 

Installation Clearances ....................................................... 5

 

Dryer Dimensions ................................................................ 5

ELECTRICAL REQUIREMENTS - U.S.A. ONLY ........................ 6

 

Grounding Instructions ....................................................... 7

ELECTRIC DRYER POWER HOOKUP - CANADA ONLY ......... 7

 

Electrical Requirements ..................................................... 7

 

Grounding Instructions ....................................................... 7

GAS DRYER POWER HOOKUP - U.S.A. AND CANADA .......... 8

 

Electrical Requirements ..................................................... 8

 

Grounding Instructions ....................................................... 8

 

Gas Supply Requirements .................................................. 8

 

Gas Type ............................................................................... 8

 

Gas Supply Line ................................................................... 8

 

Gas Supply Connection Requirements ............................. 9

 

Burner Input Requirements ................................................ 9

 

Dryer Gas Pipe ..................................................................... 9

INSTALL LEVELING LEGS .......................................................... 9

MAKE ELECTRICAL CONNECTION - U.S.A. ONLY ............... 10

 

Electrical Connection........................................................ 10

 

Power Supply Cord Connection....................................... 10

 

Direct Wire Connection..................................................... 12

MAKE GAS CONNECTION - U.S.A. AND CANADA ................ 16

VENTING .................................................................................... 16

 

Venting Requirements ....................................................... 16

 

Plan Vent System ............................................................... 17

 

Install Vent System ............................................................ 18

CONNECT VENT ....................................................................... 19

LEVEL DRYER ........................................................................... 19

COMPLETE INSTALLATION CHECKLIST ............................... 20

REVERSE DOOR SWING .......................................................... 21

TROUBLESHOOTING ............................................................... 23

INSTALLATION NOTES

Date of purchase:

 _________________________________

Date of installation:

 _______________________________

Installer:

 ________________________________________

Model number:

 ___________________________________

Serial number:

 ___________________________________

Date d’achat :

 _____________________________________

Date d’installation :

 ________________________________

Installateur :

 ______________________________________

Numéro de modèle :

 ________________________________

Numéro de série :

 __________________________________

NOTES CONCERNANT L’INSTALLATION

Table des matières

SÉCURITÉ DE LA SÉCHEUSE .................................................. 24

EXIGENCES D’INSTALLATION

 ............................................

26

 

 

Outillage et pièces ............................................................. 26

EXIGENCES D’EMPLACEMENT ............................................... 27

 

Distances de dégagement à respecter pour 

 

l’installation......................................................................... 27

 

Dimensions de la sécheuse............................................... 27 

RACCORDEMENT DE LA SÉCHEUSE  

ÉLECTRIQUE – CANADA SEULEMENT ................................... 28

 

Spécifications électriques ................................................. 28

 

Instructions de liaison à la terre ....................................... 29

RACCORDEMENT ÉLECTRIQUE DE LA SÉCHEUSE  

À GAZ - ÉTATS-UNIS ET CANADA ........................................... 29

 

Spécifications électriques ................................................. 29

 

Instructions de liaison à la terre ....................................... 29

 

Spécifications de l’alimentation en gaz ........................... 30

 

Type de gaz ......................................................................... 30

 

Canalisation de gaz ............................................................ 30

 

Spécifications du raccordement de  

 

l’alimentation en gaz .......................................................... 31

 

Spécifications de l’alimentation du bruler ....................... 31

INSTALLATION DES PIEDS DE NIVELLEMENT ...................... 31

RACCORDEMENT AU GAZ - ÉTATS-UNIS ET CANADA ........ 32

L’EVACUATION........................................................................... 32

 

 

Exigences concernant l’evacuation ................................. 32

 

 

Planification des circuits de conduits .............................. 33

 

 

Installation du système d’évacuation ............................... 34

RACCORDEMENT DU SYSTÈME D’ÉVACUATION ................. 35

ÉTABLIR L’APLOMB DE LA SÉCHEUSE .................................. 36

ACHEVER L’INSTALLATION LISTE DE VÉRIFICATION  .......... 36

INVERSION DU SENS D’OUVERTURE DE LA PORTE ............ 37

DÉPANNAGE .............................................................................. 39

Gas and Electric Dryer  

Installation Instructions

Para obtener acceso al “Instrucciones de instalación” en español, o para obtener información  

adicional acerca de su producto, visite: www.whirlpool.com 

Tenga listo su número de modelo completo. Puede encontrar el número de modelo  

y de serie dentro de la cavidad superior de la puerta.

Instructions d’installation – 

Sécheuse à gaz et électrique

Summary of Contents for WGD7500GW0

























Reviews: