background image

W10868945A 

W10868946A-SP

GAS DRYER INSTALLATION INSTRUCTIONS  

CANADIAN ELECTRIC DRYER INSTRUCTIONS

INSTRUCTIONS POUR L’INSTALLATION  

DE LA SÉCHEUSE À GAZ (É.-U. ET CANADA) 

ÉLECTRIQUE (CANADA UNIQUEMENT)

Table of Contents 

DRYER SAFETY .......................................................................... 2
INSTALLATION REQUIREMENTS .............................................. 4
 

 

Tools and Parts ...................................................................... 4

LOCATION REQUIREMENTS ..................................................... 5
ELECTRIC DRYER POWER HOOKUP-CANADA ONLY ........... 7
GAS DRYER POWER HOOKUP ................................................. 7
INSTALL LEVELING LEGS .......................................................... 9
MAKE GAS CONNECTION ....................................................... 10
VENTING .................................................................................... 10 

  Venting Requirements ......................................................... 10 

 

Plan Vent System ................................................................. 11 

 

Install Vent System .............................................................. 12

CONNECT INLET HOSE (STEAM MODEL ONLY)................... 13
CONNECT VENT ....................................................................... 14 
LEVEL DRYER ........................................................................... 15
COMPLETE INSTALLATION CHECKLIST ............................... 15
DOOR REVERSAL (OPTIONAL) ............................................... 16

INSTALLATION NOTES

Date of purchase:

 __________________________________

Date of installation:

 ________________________________

Installer:

 _________________________________________

Model number:

 ____________________________________

Serial number:

 ____________________________________

Date d’achat:

 _____________________________________

Date d’installation:

 _________________________________

Installateur:

 ______________________________________

Numéro de modéle:

 ________________________________

Numéro de série:

 __________________________________

NOTES CONCERNANT L’INSTALLATION

Para una version de estas instrucciones en español, visite www.Whirlpool.com

Table des matières

SÉCURITÉ DE LA SÉCHEUSE ................................................. 26
EXIGENCES D’INSTALLATION................................................. 28
 

 

Outillage et pièces ............................................................ 28 

EXIGENCES D’EMPLACEMENT .............................................. 29
SÉCHEUSE ÉLECTRIQUE RACCORDEMENT À 

L’ALIMENTATION ÉLECTRIQUE – CANADA SEULEMENT ... 31
RACCORDEMENT D’UNE SÉCHEUSE À GAZ ....................... 31
INSTALLATION DES PIEDS DE NIVELLEMENT...................... 33
RACCORDEMENT AU GAZ ...................................................... 34
ÉVACUATION ............................................................................ 34 

 

Exigences concernant l’évacuation ................................ 34 

 

Planification du système d’évacuation ........................... 35 

 

Installation du système d’évacuation .............................. 37

RACCORDEMENT DU TUYAU D’ALIMENTATION       

(MODÈLE À VAPEUR UNIQUEMENT) ..................................... 37
RACCORDEMENT DU CONDUIT D’ÉVACUATION ................ 39
RÉGLAGE DE L’APLOMB DE LA SÉCHEUSE......................... 39
ACHEVER L’INSTALLATION LISTE DE VÉRIFICATION .......... 40
INVERSION DE LA PORTE (FACULTATIF) ............................... 40

Summary of Contents for WGD7540FW0


























Reviews: