background image

WHISKY PARTS Co  /  6400 W 105th STREET  /  BLOOMINGTON MN, USA 55438  /  1.877.774.6217  /  info@whiskyparts.com  /  whiskyparts.com/safety

19239 09/16 | 85-000583-INST_A

Carbon Steerer Cutting

1.

   Cut the steerer tube using  

a hacksaw with a fresh 32 tpi 
tungsten carbide steel blade,  
and cutting guide. 

2.

   Remove burrs and sharp edges 

with a synthetic scouring pad. 

3.

   Clean the steerer tube and inside 

of the stem clamp using rubbing 
alcohol to remove any grease and dirt. 

 

WARNING:

 Never use a star nut with a carbon steerer tube fork  

(figure 6). Star nuts can only be used with aluminum steerer tube forks.  
Use only a compression device designed for carbon steerers.

Fork Installation

1.

   Install spacers, stem, etc. and tighten compression plug (if applicable)  

to 1.6Nm (15 in-lb). 

2.

   Insert top cap and tighten to headset/top cap manufacturer's recommend 

torque specifications. 

3.

   Tighten stem steerer clamp bolts to stem manufacturer’s recommended 

torque specifications. 

4.

   Install and adjust the front brake following the brake manufacturer’s 

instructions. 

 

WARNING:

 Failure to properly install and adjust brakes can result  

in serious injury.

5.

   Install the front wheel according to the thru-axle or quick release 

manufacturer’s instructions. 

 

WARNING:

 Failure to properly adjust the quick release or thru-axle  

to secure the wheel can result in serious injury. 

Fender Installation 

(for forks equipped with removable fender mounts)

 

WARNING:

 To avoid potential serious injury, Whisky recommends that its 

forks be used solely with ISO-approved quick-release fenders. Consult fender 
manufacturer for specific compatibility.

 

WARNING:

 Do not mount racks or any other load bearing accessory  

to the fender mounts. Doing so could result in fork breakage, causing  
a loss of control. 

1.

   Remove set screws from fender mounting holes. 

2.

   Apply Blue threadlocker onto bolts. 

3.

   Thread M5 nuts onto bolts. 

4.

   Make sure the nuts are threaded into the bolts at least 6 to 7 threads. 

5.

   Thread bolts into fork leg fender-mounting holes. 

6.

   Make sure fender mounts are threaded in at least 4 threads. 

7.

   Thread nut up to the fork leg. 

8.

   Make sure fender mount face is parallel with plane of frame and fork. 

9.

  Tighten nut to 3–4Nm to lock fender mount into position. 

Fork Preparation

1. 

  Install crown race according to manufacturer’s instructions. Do not place 

the fork on the dropout tips or crown while installing the race. Doing so 
can damage the fork and could cause failure (figure 2).

2. 

  Assemble the fork, headset and any spacers in the headtube of the 

bicycle and install the stem (figure 3). 

3.

   The spacer stack between the headset and stem must not exceed  

50mm (figure 4). 

4.

   A steerer tube must extend 7–8mm above the top of the stem clamp and 

have a 10mm spacer installed between the stem and top cap (figure 4).

5.

   Carefully measure and mark the amount of steerer tube to be removed. 

Remember that, when cut, the top of the steerer tube must be 2–3mm 
below the top of the headset spacer/stem assembly (figure 5). 

6.

   Remove the fork from the headtube.

7. 

  Make certain that you do not cut the steerer tube too short—measure 

twice, cut once.

 

WARNING:

 CYCLING CAN BE DANGEROUS. BICYCLE PRODUCTS  

SHOULD BE INSTALLED AND SERVICED BY A PROFESSIONAL MECHANIC. 
NEVER MODIFY YOUR BICYCLE OR ACCESSORIES. READ AND FOLLOW ALL 
PRODUCT INSTRUCTIONS AND WARNINGS INCLUDING INFORMATION ON 
THE MANUFACTURER’S WEBSITE. INSPECT YOUR BICYCLE BEFORE EVERY 
RIDE. ALWAYS WEAR A HELMET.
Additional safety info can be found at: whiskyparts.com/safety

Intended Use & Compatibility

For on and off-road

 riding and drops 

less than 15cm (6")

Whisky CX forks are available in a variety of steerer tube, axle, 

and brake configurations to work with your cyclocross bicycle. 
Consult with a professional bicycle mechanic to ensure that 
your new Whisky Parts Co fork is compatible with your 
cyclocross bicycle.
ASTM Condition 2: For use on paved, unpaved, and gravel 
roads and trails with moderate grades. Contact with irregular 
terrain and loss of tire contact with the ground may occur. 
Drops are intended to be limited to 15cm (6") or less.

IMPORTANT NOTE: Whisky Parts Co. recommends no less than 6mm of 
clearance between the tire, wheel, fork and frame.

Tools Required

• 

Hacksaw with a fine 32 tpi tungsten carbide steel blade

• 

Steerer tube cutting guide (recommended)

• 

Allen wrenches: 4, 5, 6mm

• 

Torque wrench that measures in Newton meters

• 

8mm box end wrench 

• 

Blue threadlocker

Stem & Headset Preparation

1.

   Verify that the fork, headset and 

all parts required for proper 
assembly have compatible 
dimensions. The fork, headset, 
headset spacers, and stem 
steerer clamp must have 
compatible diameters.  
Incorrect use of components  
can cause component failure.  
Visit headsetfitfinder.com  
to verify fork-to-frame compatibility options. Visit bicycleheadsets.com  
to learn more about headset fit and the new Standardized Headset 
Identification System (SHIS).

2.

   Make sure any stem or headset parts that come into contact with the 

steerer tube are free of burrs or sharp edges. Remove burrs or sharp 
edges with fine-grit sandpaper. 

3.

   Only use rear slot-style clamping stems on carbon steerers. Wedge-clamp 

stems must not be used and could result in failure (figure 1).

WHISKY CX FORK INSTRUCTIONS

A
B

C
D

E

F

G

H

I

 A   Compression device 
 B   10mm spacer 
 C   Spacers (50mm max) 
 D   Upper headset 
 E    Headtube 
 F   Lower headset 
 G   Fork crown race 
 H   Top of steerer tube 
 I   Fork steerer tube 
 J   Crown race seat

J

1

3

2

4

5

10mm Spacer

50mm 

MAX Spacers 

Below Stem

2-3mm

6

Reviews: